manualshive.com logo in svg

Daikin DC96SN, Service Instructions Manual, Page: 35 / 63

Share
Download
Daikin DC96SN Service Instructions Manual Download Page 35

35

f.    Remove regulator cover screw from the 

outlet pressure regulator adjust tower and 

turn screw clockwise to increase pressure or 

counterclockwise to decrease pressure. Replace 

regulator cover screw.

g.    Turn off all electrical power and gas supply to the 

system.

h.    Remove the manometer hose from the hose barb 

fitting or outlet pressure boss.

i.    Remove the 1/8” NPT hose barb fitting from the 

outlet pressure tap. Replace the outlet pressure 

boss plug and seal with a high quality thread 

sealer.

WARNING

HIGH VOLTAGE

Disconnect ALL electrical power and shut off 

gas supply before servicing or installing this 

unit. Multiple power sources may be present. 

Failure to do so may cause property damage, 

personal injury or death.

7.  Turn on gas to furnace and check for leaks. If 

leaks are found, repair and then reinstall burner 

compartment door.

8.  Turn on electrical power and verify proper unit 

operation.

Pressure Regulator

Adjustment 

(Under Cap Screw)

Gas Valve

On/Off

Selector

Switch

INLET

OUTLET

Inlet Pressure

Tap

Outlet Pressure

Tap

White-Rodgers Model 36J22 (Single-Stage) 

Gas Valve On/Off

Selector Switch

Inlet

Pressure

Tap

Pressure Regulator

(under cap screw)

Outlet

Pressure

Tap

Honeywell Model VR8215 

Gas

Rate

Range

Nominal 

High Stage  9.7 to 10.3" w.c. 10.0" w.c. 

Low Stage 5.7 to 6.3" w.c. 6.0" w.c. 

Propane Gas

Manifold Gas Pressure 

S-308  Checking Hot Surface Ignitor

Single stage furnaces use a 115 volt silicon carbide igniter 

(p/n 0130F00008) with 17-second warm up time.

WARNING

Disconnect ALL power before servicing.

1.  Remove burner compartment door to gain access to 

the ignitor.

2.  Ignitor cool  -  approximately 70 - 77°F.

3.  Disconnect the ignitor from the Ignition Control.

4.  Using an ohmmeter measure the resistance of the 

ignitor: at room temperature a normal reading will be 

37 - 68 ohms.

5.  Reconnect ignitor.

WARNING

Line Voltage now present.

6.  Place unit in heating cycle, measure current draw of 

ignitor during preheat cycle.

a.    Turn off all electrical power and gas supply to the 

system.

b.    Remove the manometer hose from the outlet 

pressure boss.

c.     Remove the 1/8” NPT hose barb fitting from the 

outlet pressure tap.  Replace the outlet pressure 

boss plug and seal with a high quality thread 

sealer.

WARNING

HIGH VOLTAGE

Disconnect ALL electrical power and shut off gas supply 

before servicing or installing.

7.  Turn on gas to furnace and check for leaks. If 

leaks are found, repair and then reinstall burner 

compartment door.

8.  Turn on electrical power and verify proper unit 

operation. Make sure furnace operates at the proper 

manifold pressure at both high and low stage outputs.

SERVICING

Summary of Contents for DC96SN
































































Reviews:

No comments