background image

2

Important Safety Instructions

The following symbols and labels are used throughout this 

manual to indicate immediate or potential safety hazards. 

It is the owner’s and installer’s responsibility to read 

and comply with all safety information and instructions 

accompanying these symbols. Failure to heed safety 

information increases the risk of personal injury, property 

damage, and/or product damage.

WARNING

HIGH VOLTAGE

Disconnect all power before servicing or 

installing this unit. Multiple power sources 

may be present. Failure to do so may cause 

property damage, personal injury or death. 

To avoid property damage, personal injury or death due to 

electrical shock, this unit MUST have an uninterrupted, 

unbroken electrical ground. The electrical ground 

circuit may consist of an appropriately sized electrical 

wire connecting the ground lug in the unit control box 

to the building electrical service panel. Other methods 

of grounding are permitted if performed in accordance 

with the National Electric Code (NEC) / American National 

Standards Institute (ANSI) / National Fire Protection 

Association (NFPA) 70 and local/state codes. In Canada, 

electrical groundings is to be in accordance with the 

Canadian Electrical code (CSA) C22.1.

WARNING

CAUTION

When installing or servicing this equipment, safety 

clothing, including hand and eye protection, is strongly 

recommended. If installing in an area that has special safety 

requirements (hard hats, etc.), observe these requirements.

Do not connect to or use any device that is not design-

certified by the manufacturer for use with this unit. 

Serious property damage, personal injury, reduced unit 

performance and/or hazardous conditions may result from 

the use of such non-approved devices.

WARNING

To prevent the risk of property damage, personal injury, 

or death, do not store combustible materials or use 

gasoline or other flammable liquids or vapors in the 

vicinity of this unit.

WARNING

This airhandler is designed for Upflow or Horizontal-

Left applications. DO NOT INSTALL IN THE DOWNFLOW OR 

HORIZONTAL-RIGHT ORIENTATION.

WARNING

 

 

 

 

 

Carbon monoxide producing devices (such as an automobile, space

heater, gas water heater, etc.) should not be operated in enclosed areas

such as unvenlated garages, ulity rooms or parking areas because of

the danger of carbon monoxide (CO) poisoning resulng from the exhaust

emissions.  If a furnace or air handler is installed in an enclosed area such

as a garage, ulity room or parking area and a carbon monoxide producing

device is operated therein, there must be adequate, direct outside

venlaon.

 

 

 

CARBON MONOXIDE POISONING HAZARD

 

Special Warning for Installaon of Furnace or Air Handling Units in

Enclosed Areas such as Garages, Ulity Rooms or Parking Areas

This venlaon is necessary to avoid the danger of CO poisoning which

can occur if a carbon monoxide producing device connues to operate in

the enclosed area.  Carbon monoxide emissions can be (re)circulated

throughout the structure if the furnace or air handler is operang in any

mode.

B10259-216

CO can cause serious illness including permanent brain

damage or death.

Los equipos ó aparatos que producen monóxido 

(tal como automóvil, calentador de gas, calentador de 

carbono (CO) que resulta de las

emisiones de gases de combusón.  

gas, etc) no deben ser operados en áreas cerradas debido al riesgo

de envenenamiento por monóxido de 

Si el equipo ó aparato se opera en

dichas áreas, debe exisr una adecuada venlación directa al exterior. 

de carbono

agua por medio de

 

Advertencia especial para la instalación de calentadores ó manejadoras 

de aire en áreas cerradas como estacionamientos ó cuartos de servicio.

 

 

 

 

B10259-216

RIESGO DE INTOXICACIÓN POR MONÓXIDO DE CARBONO

El monóxido de carbono puede causar enfermedades severas 

como  daño cerebral permanente ó muerte.

Las emisiones de monóxido de carbono pueden circular a través

del aparato cuando se opera en cualquier modo. 

 

Averssement special au sujet de l'installaon d'appareils de chauffage

ou de traitement d'air dans des endroits clos, tets les garages, les

locaux d'entreen et les staonnements. 

 

 

 

B10259-216

RISQUE D'EMPOISONNEMENT AUMONOXYDE DE CARBONE

Evitez de mere en marche les appareils produisant du monoxyde

de carbone (tels que les automobile, les appareils de chauffage

autonome,etc.)  dans des endroits non venlés tels que les

d'empoisonnement au monoxyde de carbone. Si vous devez faire

fonconner ces appareils dans un endroit clos, assures-vous 

qu'il y ait une venlaon directe provenant de l'exterier.  

Le monoxyde de 

des 

carbone peut causer des maladies graves telles que

dommages permanents au cerveau et meme la mort.

Les émissions de monoxyde de carbone peuvent etre recircules dans les

endroits clos, si l'appareil de chauffage ou de traitement d'air sont

en marche. 

Cee venlaon est nécessaire pour éviter le danger d'intoxicaon

au CO pouvant survenir si un appareil produisant du monoxyde 

de carbone connue de fonconner au sein de la zone confinée.

Esta venlación es necesaria para evitar el peligro de envenenamiento

por CO, que puede ocurrir si un 

monóxido

de carbono sigue operando en el lugar cerrado.

disposivo que produce 

Summary of Contents for DAX Series

















Reviews: