background image

5

English

Indoor Unit Installation

Intelligent-eye sensor

CAUTION

1) Do not hit or violently push the Intelligent-eye sensor. This can lead to damage and malfunction.
2) Do not place large objects near the sensor. Also keep heating units or humidifiers outside the sensor’s detection area.

A

M4 × 16L

Screws 
(Field supply: M4 × 25L)

Screws 
(Field supply: M3 × 20L)

 D  
Wireless 
remote 
controller

 E  
Remote 
controller holder

Before screwing the remote 
controller holder to the wall, 
make sure that control 
signals are properly 
received by indoor unit.

Service lid

Opening service lid

Service lid is opening/closing type.

Opening method

1) Remove the service lid screws.
2) Pull out the service lid diagonally

down in the direction of the arrow.

3) Pull down.

Intelligent-eye sensor

Wrap the insulation pipe with 
the finishing tape from bottom 
to top.

Cut thermal insulation 
pipe to an appropriate 
length and wrap it with 
tape, making sure that no 
gap is left in the insulation 
pipe’s cut line.

Caulk 
pipe hole 
gap 
with putty. 

Mounting
plate

Clip

Mark (rear side)

Bottom frame

Front grille

How to attach the indoor unit.

Hook the claws of the bottom frame
to the mounting plate.
If the claws are difficult to hook,
remove the front grille.

How to remove the indoor unit.

Push up the marked area (at the
lower part of the front grille) to
release the claws. If it is difficult to
release, remove the front grille.

The mounting plate 
should be installed on a 
wall which can support the 
weight of the indoor unit.

30mm or more from ceiling

Front panel

50mm or more from walls 
(on both sides)

Air filters

Titanium Apatite Photocatalytic 
Air-Purifying Filter (2)

A

Mounting plate

Air filter

Titanium Apatite 
Photocatalytic 
Air-Purifying Filter

Filter frame

Tab

B

01_EN_3P212421-1.fm  Page 5  Wednesday, September 26, 2007  5:57 PM

Summary of Contents for ATXS20E2V1B
















Reviews: