manualshive.com logo in svg

Daikin ATXG25EV1B, Installation Manual

Share
Download
Daikin ATXG25EV1B Installation Manual Download Page 7

5

■

English

Indoor Unit Installation Drawings

Intelligent-Eye Sensor

CAUTION

1) Do not hit or violently push the Intelligent-eye sensor. This can lead to damage and malfunction.
2) Do not place large objects near the sensor. Also keep heating units or humidifiers outside the sensor’s detection area.

Use when 
opening the 
front panel and 
securing.

Supporting plate

Supporting plate

Cut thermal insulation 
pipe to an appropriate 
length and wrap it with 
tape, making sure that no 
gap is left in the insulation 
pipe’s cut line.

Caulk pipe hole gap 
with putty. 

30mm or more 
from ceiling

Front panel

50mm or more from walls 
(on both sides)

Outlet vent panel

Screws (Field supply)

The mounting plate should be installed 
on a wall which can support the weight 
of the indoor unit.

A

Mounting plate

Installing and removing the indoor unit

   Attaching the indoor unit
1) Using the 2    marks on top of the indoor 

unit, attach the     mounting plate hooks 
onto the indoor unit.

2) Attach the tabs on the bottom frame firmly 

onto the     mounting plate. 
(2 on either side)

   Removing the indoor unit
1) Lift the marked parts on the bottom of the 

front grill, pull the front grill towards 
yourself and disengage the tabs on the 
bottom of the frame.

2) Lift up the indoor unit and remove it from 

the top of the mounting plate.

See 

4. How to open the indoor unit 

service lid

 on p4 of the Installation 

Tips for details.

Titanium Apatite 
Photocatalytic Air-Purifying Filter

Install Titanium Apatite Photocatalytic 
Air-Purifying Filter on air filter

Air filters

B

Air filter

B

Titanium Apatite 
Photocatalytic 
Air-Purifying Filter

C

Screws
(Field supply)

D

Remote 
controller 
holder

Wireless 
remote 
controller

Before screwing the remote 
controller holder to the wall, make 
sure that control signals are 
properly received by indoor unit.

Appearance of the indoor unit may 
differ from some models.

A

Mounting 
plate

Marked 
part (rear)

Bottom frame

Tab

A

Mounting 
plate

A

A

Secure the installation plate to the wall on 
the side where the bottom frame and the 
installation plate are secured to each other.

Cushioning material 
(do not remove)

01_EN_3P166464-1.fm  Page 5  Saturday, September 17, 2005  11:08 AM

Summary of Contents for ATXG25EV1B
















Reviews:

No comments

Brands by name

Popular brands

Load more brands