manualshive.com logo in svg

Daikin ATXG25EV1B, Installation Manual

Share
Download
Daikin ATXG25EV1B Installation Manual Download Page 13

11

■

English

Refrigerant Piping Work

2-2. Selection of Copper and Heat Insulation materials

• When using commercial copper pipes and fittings, observe the 

following:

1) Insulation material:  Polyethylene foam

Heat transfer rate:  0.041 to 0.052W/mK (0.035 to 0.045kcal/mh

°

C)

Refrigerant gas pipe’s surface temperature reaches 110

°

C max.

Choose heat insulation materials that will withstand this temperature.

2) Be sure to insulate both the gas and liquid piping and to provide insulation dimensions as below.

3) Use separate thermal insulation pipes for gas and liquid refrigerant pipes.

Gas side

Liquid side

25/35 class

50 class

25/35/50 class

O.D. 9.5mm

O.D. 12.7mm

O.D. 6.4mm

Thickness 0.8mm

Thickness 0.8mm

Gas pipe thermal insulation

Liquid pipe thermal insulation

25/35 class

50 class

25/35/50 class

I.D. 12-15mm

I.D. 14-16mm

I.D. 8-10mm

Thickness 10mm Min.

Gas pipe

Liquid pipe

Gas pipe

insulation

Liquid pipe

insulation

Finishing tape

Drain hose

Inter-unit wiring

01_EN_3P166464-1.fm  Page 11  Saturday, September 17, 2005  11:08 AM

Summary of Contents for ATXG25EV1B
















Reviews:

No comments

Brands by name

Popular brands

Load more brands