Daikin ARQ Installation And Maintenance Manual Download Page 30

Page: 30 / 44

IM 1083-3

30 www.DaikinApplied.com

MicroTech

Unit Electrical

Connections

DANGER

To avoid electrical shock, personal injury or death, be

sure that field wiring complies with local and national fire,

safety, and electrical codes, and voltage to the system is

within the limits shown in the job-specific drawings and

unit electrical data plate(s).

WARNING

Power supply to unit must be disconnected before making field

connections. To avoid electrical shock, personal injury or death,

be sure to rigorously adhere to field wiring procedures regarding

proper lockout and tagout of components.

See "Electrical Data" on page

page 29

, and

Figure

43 page 26 and Figure 44

or the job-specific electrical

drawings before proceeding with field power and control wiring.

See also the wiring diagram provided on the unit ventilator

inside-right front access panel.

Unit ventilators equipped with an optional electric heating coil

have electric heating coil power connections at right end only.

Procedure

1. Provide power supply to right end compartment to match

unit nameplate.

CAUTION

Use copper conductors only. Use of aluminum conductors may

result in equipment failure and overheating hazards. All wiring in

right hand compartment must be class 1.

Figure 45: Electrical power On/Off switch located behind

front-middle access panel in wire trough, with power entry

accessed behind right-front access panel

Grommeted Power Wire Entry

Unit Main Power

On/Off Switch

2. Confirm that power is de-energized and locked and

tagged-out.

3. Plug in the unit control wiring male plug(s) into the

appropriate female plug(s).

•

Plug in 4-pin (for MicroTech and Electromechanical, see

Figure 48 on page 31).

•

0-pin (MicroTech only, see Figure 49 on page 31).

•

12-pin (MicroTech only, see Figure 50 on page 31).

4. Insert the main power wires into the main power On/Off

switch terminal lugs (A, B and C). Note that terminal lug

B, not used on single phase. Connect the Ground wire to

the ground lug as shown in Figure 47. Tighten the terminal

lugs securely.

5. Reinstall the cover plate on the main power wire trough.

Note: For Electromechanical wiring (see Figure 58 on page

36).Control connections for elecromechanical are

made to the terminal block in the left end compartment.

Figure 46: Control wiring plug connections in right end

compartment.

Control wiring whips with

caps located in the right

front end compartment

Figure 47: Electrical power On/Off switch for power wiring

connections

Note:

not used on single phase.

Terminal lugs for main power wiring from unit,

field connection by others

Main Power On/Off Switch

Ground Lug

Summary of Contents for ARQ













































Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands

Daikin ARQ, Installation And Maintenance Manual

Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands