Daikin ARQ, Installation And Maintenance Manual

Page: 28 / 44

IM 1083-3 28 www.DaikinApplied.com
Table 10: Wiring Diagram Legend for Figure 43 on page 26 and Figure 44 on page 27
Symbol Description Symbol Description Symbol Description
A1 Actuator- Outdoor Air HP High Pressure Switch R32 Relay - Drain Pan Heater
A2 Actuator- Face & Bypass ICT Sensor - Indoor DX Coil Temperature R28 Relay - Outdoor Motor Air
CP1 Motor Compressor 2-Stage IH Sensor - Indoor Humidity RV Reversing Valve
C1 Compressor Contactor MCB Main Control Board RAT Sensor - Room Air Temperature
CAP1 Capacitor Run NTWK Network Connection T6 Thermostat - Freeze Stat
CEH1-3 Electric Heat Contactor OAT Sensor - Outdoor Air Temperature TB1 Terminal Block - 24VAC+
CO2 Sensor - Indoor Air CO2 OCT Sensor - Outdoor DX Coil Temperature TB2 Terminal Block – 24VAC Gnd
DAT Sensor - Discharge Air Temperature OH Sensor - Outdoor Humidity TB3 (A, B) Terminal Block – Main Power
DCS Switch - Unit Power OH1 Thermostat - Overheat TBE Terminal Block - Electric Heat
DF Dead Front Switch OH2 Thermostat - Overheat TR1 Transformer - Motor Speed
EH1-6 Heater - Electric OHM E.H. Man Reset - Overheat Stat TR3 Transformer - 208 / 230V-24V, 75VA
EH10 Heater - Outdoor Drain Pan PL1 LED Occupancy / Fault Status TR4 Transformer - 460V–230V
F1A/F1B Fuse - Compressor R1-R3 Relay Electric Heat (Backup) TR5 Transformer - 208 / 230V-24V
F2A/F3C Fuse - Electric Heat R10-R12 Relay – Electric Heat V1 Valve - Heat EOC (Accessory)
FA/FB Fuse– Control, Load R4H Relay – Fan High Speed V2 Valve - Cool EOC (Accessory)
FC/FD Fuse– Control, Transformer R4M Relay– Fan Medium Speed VH Valve - Heat (Accessory)
FMI Motor - Room Fan R4L Relay– Fan Low Speed VC Valve - Cool (Accessory)
FMO Motor Outdoor Air
Notes: 1. All electrical installation must be in accordance with national and local electrical codes and job wiring schematic.
External wiring options - see IM for the different configured options, wiring to be minimum 18 gauge, 90°C.
3. EC motors are factory programmed for specified air flow. Contact Daikin Applied for replacement.
4. Cap extra wire. Switch wire 42A to red wire for 208V operation.
5. Switch wire 509 to terminal 2 for 208V operation.
6. Devices in legend may or may not be on unit.
Electrical Data
ARQ & GRQ – Size 024
Volt/Hz/Phase
Voltage Range
Room Fan
FLA
Compressor Heating Option Power Supply
Min. Max. RLA LRA Heat Type
Heater
Kw
Rated
Heater
Amps
MCA
Maximum
Fuse
208/60/1 197 228
2.7 11.7 58.3 None – – 17.3 25
2.7 11.7 58.3
Elec. Heat1
Low (3 elem.) 8.0 38.5 65.4 70
2.7 11.7 58.3 High (6 elem.) 16.0 76.9 113.5 125
230/60/1 207 253
2.7 11.7 58.3 None – – 17.3 25
2.7 11.7 58.3
Elec. Heat1
Low (3 elem.) 7.3 33.3 59.0 60
2.7 11.7 58.3 High (6 elem.) 14.7 66.7 100.7 110
208/60/3 197 228
2.7 6.5 55.4 None – – 10.8 15
2.7 6.5 55.4
Elec. Heat1
Low (3 elem.) 8.0 22.2 38.6 40
2.7 6.5 55.4 High (6 elem.) 16.0 44.4 66.3 70
230/60/3 207 253
2.7 6.5 55.4 None – – 10.8 15
2.7 6.5 55.4
Elec. Heat1
Low (3 elem.) 7.3 19.2 34.9 35
2.7 6.5 55.4 High (6 elem.) 14.7 38.5 58.9 60
460/60/3 414 506
2.7 3.5 28.0 None – – 7.1 15
2.7 3.5 28.0
Elec. Heat1
Low (3 elem.) 7.3 9.6 19.1 20
2.7 3.5 28.0 High (6 elem.) 14.7 19.2 31.1 35
1
Electric Heat Options are without Compressor and Outdoor Fan.
2.