Daikin ARQ Installation And Maintenance Manual Download Page 31

Page: 31 / 44

www.DaikinApplied.com 31

IM 1083-3

Figure 48: 4-pin plug MicroTech control wiring diagram

Communication

Module

(4-pin)

Male Connector

Unit Ventilator

Optional Building Automation System (BAS)

Wiring:

Use twisted shielded pair (Connect Air W221P-2544 or equivalent).

Daisy-chain and tie shield to earth ground at

one

point only.The polarity of the signal must always be

maintained throughout the network. Always c to + and - to -. The shield connection must be

continuous throughout the entire network and must be connected to earth ground at

one

(and only one) point.

The N2 Bus can use either solid or stranded wires of the following types:

3-wire twisted cable, 2 twisted-pair telephone cable, or two twisted pair with shield.

The wiring is polarity sensitive. The polarity of the signal must always be maintained

throughout the network. Always c to + and - to -. The shield connection must

be continuous throughout the entire network and must be connected to earth ground at

one

(and only one) point.

Use Belden 8471, NEMA Level 4, or Echelon-approved equivalent wire. Since the L

ORKS

communication

wiring is polarity insensitive, no polarity must be observed when making connections via the unshielded twisted-pair wiring.

ORKS

FTT–10 (A)

FTT–10 (B)

BACnet

GND

(4-pin)

Female Connector

Black

Red

GND

RT-

RT+

(By others)

Figure 49: 10-pin plug MicroTech wiring diagram

Unit Ventilator

DO7

DO8-NO
DO8-NC

DO5

Connector

Wire

Caps

UVC

601A
602A
603A
604A
605A
606A
607A
608A
609A
610A

DO8-Comm

TB2 - 24VAC Comm

DO13

24VAC+

Empty

External Output

Option 1 Device

(by Others)

Pump or Motorized

Valve

Normally Open

Factory Wiring
Field Wiring (by Others)
External Device (by Others)

External Output

Option 3 Device

(by Others)

Exhaust Fan

Signal

External Output

Option 2 Device

(by Others)

Fault Indication

Shield

Note: Not all external input options are available for all models.
Figure 50: 12-pin plug MicroTech control wiring diagram
Note: Not all external input options are available for all models.

External Input

Option 3 Device

(by others)

Ventilation Lockout

(default) or

Exhaust Interlock

External Input

Option 2 Device

(by others)

Remote

Shutdown

External Input

Option 1 Device

(by others)

Unoccupied (default)

or Dewpoint Humidity

P1 (12-pin)

Connector

Unit Ventilator

P1 (12-pin)

Connector

Wall Sleeve

H6-8

H6-7

H6-6

H6-5

H6 4

H6-3

H6-1

H6-2

910

911

902

901

912

909

907

906

Remote Wall Sensor

(Option)

GND

UTS

OCC

24VAC

896

907

904

905

908

896

H6-1

H4-1

H4-2

H5-3

H5-4

24VAC

Shield

TB1 - 24VAC

Wire

Caps

TB1 - 24VAC

Not Used

Summary of Contents for ARQ













































Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands

Daikin ARQ, Installation And Maintenance Manual

Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands