Daikin ARQ Installation And Maintenance Manual Download Page 6

Page: 6 / 44

IM 1083-3

www.DaikinApplied.com

Safety

Follow all safety codes. Wear safety glasses and work gloves.

Use a quenching cloth for brazing operations. Have a fire

extinguisher available. Follow all warnings and cautions in

these instructions and attached to the unit. Consult applicable

local building codes and National Electrical Codes (NEC) for

special requirements.

Recognize safety information. When you see a safety symbol

on the unit or in these instructions, be alert to the potential for

personal injury. Understand the meanings of the words

DANGER, WARNING, and CAUTION. DANGER identifies

the most serious hazards that will result in death or severe

personal injury; WARNING means the hazards can result in

death or severe personal injury; CAUTION identifies unsafe

practices that can result in personal injury or product and

property damage.

Improper installation, adjustment, service, maintenance, or use

can cause explosion, fire, electrical shock, or other conditions

which may result in personal injury or property damage. This

product must be installed only by personnel with the training,

experience, skills, and applicable licensing that makes him/her

“a qualified professional HVACR installer.”

DANGER

Disconnect all electrical power before servicing unit.

Electrical shock will cause severe injury or death.

WARNING

Hazardous Voltage!Use copper conductors only. Unit terminals

are not designed to accept other types of conductors. Failure to

do so may cause damage to the equipment.

CAUTION

Personal injury hazard. Wear protective gloves to avoid possi-

ble cuts and abrasions from exposed edges. Avoid contact with

sharp edges.

WARNING

Cleaning agents may cause serious damage to internal compo-

nents, such as aluminum coils and electronic controls, etc. Do

not operate unit ventilator while building maintenance cleaning

agents are in use.

eneral

ata

Table 1: Approximate shipping weights, physical data

024

040

048

Overall Unit Dimensions

86"w × 30"h × 16⅝"d or

(21⅞"d w/Adapter Back)

98"w × 30"h × 16⅝"d or

(21⅞"d w/Adapter Back)

110"w × 30"h × 16⅝"d or

(21⅞"d w/Adapter Back)

Fan Data

Nominal CFM (L/s)

High Speed

1000 (472)

1250 (590)

1500 (708)

Medium speed

750 (354)

1000 (472)

1150 (543)

Low Speed

650 (307)

800 (378)

950 (448)

Number of Fans

Size

Diameter - in (mm)

8.12 (206mm)

Width- in (mm)

8.25 (210mm)

Room Fan Motor Horsepower

1/4

Filter Data

Nominal Size

10 x 48½ x 1

10 x 60½ x 1

(2) 10 x 36½ x 1

(mm)

254 x 1232 x 25

254 x 1537 x 25

(2) 254 x 927 x 25

Area - Ft

3.37 (.31)

4.2 (.39)

5.08 (.47)

Quantity

Shipping Weight

lb (kg)

690 (310)

720 (325)

760 (340)

Refrigerant Charge

132

109

Summary of Contents for ARQ













































Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands

Daikin ARQ, Installation And Maintenance Manual

Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands