background image

IM 1240-4 • INTELLIGENT EQUIPMENT 34 www.DaikinApplied.com

Installation

Ethernet LAN Configuration

NOTE: 

Ethernet LAN is one of three possible methods 

of cloud connectivity. The method of connectivity 

is specified at the time of order. You should 

only configure the gateway for Ethernet LAN 

connectivity if certain that Ethernet LAN was 

specified at the time of order. If unsure, contact the 

salesperson or Daikin Applied Controls Technical 

Response Center. Prior to configuring the gateway 

for Ethernet LAN, please refer to Appendix A of this 

document for required IT information.

The M2M Gateway is configured using a set of HTML interface 

pages within the Wind River Intelligent Device Platform. 

The table below indentifies the Wind River configuration 

parameters, along with the corresponding physical port 

on the M2M Gateway. For reference, it also includes the 

corresponding device connection to the M2M Gateway. 

Wind River 

configuration 

parameter

M2M Gateway port

Device Connection

LAN

ETH (which is eth0)

MTIII Unit Controller

wan

USB2 (which is eth1)

Local Network

wlan0

WLAN

WiFi

wwan

3G/GPRS

Cellular 

The following procedures should be used to configure the 

Intelligent Equipment solution for Ethernet LAN connectivity 

(

NOTE:

 it is the “wan” interface in the gateway that will be 

configured).

1.  Remove the USB-to-Ethernet converter from the 

envelope and connect it to an open USB port on the 

M2M Gateway (this is necessary because the M2M 

Gateway has a single Ethernet plug, which is connected 

to the MicroTech III controller, and, therefore, unavailable 

for the purpose of connecting to the local network).

a.  Connect the provided Ethernet patch cable to the 

USB-to-Ethernet adapter and to the local network 

(DHCP is enabled by default).

2.  Using a laptop computer and Ethernet cable, connect 

to the “ETH” port of the M2M Gateway (you will need to 

temporarily disconnect the Ethernet cable between the 

M2M Gateway and the MicroTech III controller, to make 

use of the “ETH” port on the M2M Gateway).

3.  Navigate to your laptop’s Local Area Connection settings 

screen and change the IP subnet mask to 

255 .255 .0 .0

and set the IP address to be compatible with the default 

M2M Gateway IP address of 

https://172 .31 .255 .1

 

(example compatible address: 172.31.255.7). For 

more information on how to change your computer’s IP 

settings, consult the Operating System’s “Help” files. 

4.  Temporarily disable the wireless adapter(s) on the 

computer, as these may prevent accessing the HTML 

Interface page. 

5.  Open a web browser and type, https://172.31.255.1, then 

press enter.

a.  When prompted, enter the User Name: “service”.
b. 

Enter the unique password that was provided with 

the Gateway hardware and press ENTER.

c.  This opens the Wind River Intelligent Device 

Platform configuration page in the gateway (

Figure 

75 on page 35

).

NOTE: 

If you will use DHCP for your local network 

configuration, please proceed to step 8. 

6.  Click the ‘Network’ tab
7. 

Locate the ‘wan Configuration’ section (

Figure 76 on 

page 36

)

a. 

Under wan Configuration select ‘Static IP’ for 

Connection Type

b.  Ensure that Interface = eth1

c.  Enter the IP, Subnet, and Gateway address 

information

d.  Under wan DNS Servers enter your network’s 

primary DNS server and click ‘Add’ (NOTE: If you 

prefer to use a public DNS server, use 8.8.8.8 or 

4.2.2.2)

e.  If a secondary DNS server address is to be 

entered, enter it after the page has reloaded and 

click ‘Add’ and enter the secondary address.

8.  Click the ‘Save Changes’ button in the lower right corner 

of the page. Then, click 

‘Apply Changes’

.

a. 

IMPORTANT:

 Allow the page to refresh

b. 

Confirm that there is number in parentheses next 

to “Review Changes”. If so, proceed to step 7; if 

not, repeat steps 5 and 6.

9.  Click the ‘Apply Changes’ button in the lower right-hand 

corner of the screen. The page will automatically refresh 

when complete (this can take as much as two minutes).

10.  Click the ‘Multiwan’ tab

a.  Scroll to the bottom of the page and Click ‘Add 

New Interface’ (

Figure 77 on page 36

)

b.  Name the interface, “wan” (must match the name 

of the interface configured in step 5.

c.  Click ‘Add new interface’

Summary of Contents for AGZ-D















































Reviews: