background image

English

5

Outdoor Unit Installation Guideline

• Where a wall or other obstacle is in the path of outdoor unit’s inlet or outlet airflow, follow the installation guidelines below.
• For any of the below installation patterns, the wall height on the exhaust side should be 1200mm or less.

Selecting a Location for Installation of 

the Indoor Units

• The maximum allowable length of refrigerant piping, and the maximum allowable height difference between the outdoor and 

indoor units, are listed below.
(The shorter the refrigerant piping, the better the performance. Connect so that the piping is as short as possible. 

Shortest allow-

able length per room is 3m.

)

Outdoor unit capacity class

2MXS52, 2AMX52, 3MXS40, 3MXS52, 3AMX52, 3MKS50, 4MKS58

Piping to each indoor unit

25m max.

Total length of piping between all units

50m max.

If the outdoor unit is positioned higher than the 
indoor units.

If the outdoor unit is positioned otherwise.
(If lower than one or more indoor units)

Wall facing one side

Side view

More than 100

Direction 
of air

More than 350

1200
or less

Walls facing two sides

Top view

More than 50

More than 50

More 
than 100

More 
than 350

unit: mm

Walls facing three sides

Top view

More than 50

More than 100

More than 350

(only heat
pump models)

Level  
difference: 
15m max.

Level  
difference: 
7.5m max.

Indoor Unit

Outdoor Unit

(only heat
pump models)

Level 
difference: 
7.5m max.

Level  
difference: 
15m max.

Outdoor Unit

Indoor Unit

01_EN_3P164392-4P.fm  Page 5  Tuesday, October 30, 2012  11:08 AM

Summary of Contents for 3MXS40K2V1B
























Reviews: