background image

English

4

Indoor/Outdoor Unit 

Installation Drawings

For installation of the indoor units, refer to the installation manual which was provided with the units.
(The diagram shows a wall-mounted indoor unit.)

 CAUTION

• Do not connect the embedded branch piping and the outdoor unit when only carrying out piping work without connecting the 

indoor unit in order to add another indoor unit later.
Make sure no dirt or moisture gets into either side of the embedded branch piping.
See “7 Refrigerant piping work” on page 9 for details.

• It is impossible to connect the indoor unit for one room only. 

Be sure to connect at least 2 rooms

.

Caulk 
pipe hole 
gap 
with putty. 

Cut thermal insulation 
pipe to an appropriate 
length and wrap it with 
tape, making sure that no 
gap is left in the insulation 
pipe’s cut line.

Wrap the insulation 
pipe with the finishing 
tape from bottom to top.

250mm from wall

Allow space for piping 
and electrical servicing.

If there is the danger of the unit falling 
or overturning, fix the unit with 
foundation bolts, or with wire or other 
means.

If the location does not have good 
drainage, place the unit on a level 
mounting base (or a plastic pedestal). 
Install the outdoor unit in a level 
position. Failure to do so may result in 
water leakage or accumulation.

Level mounting 
base (optional parts)

(Foot bolt-

hole centres)

600

Clamping material

Insulation tube

Service lid

Tape

Also insulate the connection on the outdoor unit.

Use tape or insulating material on all connections 
to prevent air from getting in between the copper 
piping and the insulation tube.
Be sure to do this if the outdoor unit is installed 
above.

(Foot bolt-hole 

 centres)

353

Stop valve cover

Allow 300mm of 
work space below 
the ceiling surface.

unit: mm

Max. allowable refrigerant charge amount

3MXM40M

2.2kg

3(A)MXM52M

2.2kg

3MXM68M

2.4kg

4MXM68M

2.6kg

4MXM80M

3.0kg

5MXM90M

3.3kg

Refrigerant piping must be kept to 
a minimum.

3MXM40M

4.7m

2

3(A)MXM52M

4.7m

2

3MXM68M

5.5m

2

4MXM68M

6.5m

2

4MXM80M

8.6m

2

5MXM90M

10.4m

2

Minimum floor area for installation

The flare connection 
should be installed 
outdoors.

Refrigerant piping must 
be protected from 
physical damage. 
Install a plastic cover or 
equivalent.

Summary of Contents for 3MXM40M2V1B





























Reviews: