background image

English

14

Wiring

 CAUTION

¨

Ground

This air conditioner must be grounded. For grounding, follow all local, and state electrical codes.

Standby Electricity Saving

The standby electricity saving function turns off power supply to the outdoor unit and sets the indoor unit into 
standby electricity saving mode, thus reducing the power consumption of the air conditioner.
The standby electricity saving function works on the following indoor unit.

 CAUTION

• The standby electricity saving function cannot be used for models other than the specified ones.

Procedure for turning on standby electricity saving 
function

1) Check that the main power supply is turned off. Turn it 

off if it has not been turned off.

2) Remove the stop valve cover.
3) Disconnect the selective connector for standby 

electricity saving.

4) Turn on the main power supply.

 CAUTION

• Before connecting or disconnecting the selective connector for standby electricity saving, make sure that the main power 

supply is turned off.

• The selective connector for standby electricity saving is required if an indoor unit other than the above applicable one is connected.

Good

Round crimp-
style terminal

Flat washer

Screw

Wrong

Flat washer

Round crimp-
style terminal

Screw

Flat washer

Screw

Round 
crimp-style 
terminal

A

Arrow view 

A

 

Stranded 
wire

Round crimp-style
terminal

Precautions to be taken for power supply wiring. When using 
stranded wires, make sure to use the round crimp-style terminal 
for connection to the power supply terminal 

Strip wire end
to this point.

Excessive strip length
may cause electric shock 
or current leakage.

Stripping wire at terminal block

Good

Wrong

Good

Wrong

When connecting the inter-unit wires to the terminal block using a single core wire, 
be sure to curl the end of the lead. Improper work may cause heat and fires.

1-3

A

B

A<B

• Make sure that the 

earth wire between 
the pull relief and 
terminal is longer 
than the other 
wires.

3MXM40M, 3MXM52M, 3AMX52M only

For FTXM, FTXP, FTXJ type

Standby electricity saving 
function off.

Standby electricity saving 
function on.

The standby electricity saving function is turned off before shipping.

Summary of Contents for 3MXM40M2V1B





























Reviews: