Dahua NVS0104HDC User Manual Download Page 92

Page: 92 / 120

Dahua Network Video Server

User’s Manual

number

Enable tour

Check the box here to enable tour function.

Interval

Here is for you to adjust transparency. The value ranges from 5 to
120s. The default setup is 5s.

Split

Here  you  can  set  window  mode  and  channel  group.  System  can
support  1/4/8/9/16/25/36-window  according  to  device  channel
amount.

Motion
tour/Alarm
tour

Here you can set motion detect tour/alarm tour window mode.
System supports 1/8-window now.

4.4.5.2.3 Zero-channel Encoding

From main menu->Setup->System->Zero-channel encoding, the interface is shown as in

Figure 4-102.

Figure 4-102

Please refer to the following sheet for detailed information.

Parameter

Function

Enable

This function is disabled by default. Check the box here to enable

this function so that you can control the zero-channel encoding

function at the WEB.

Compression System default setup is H.264. You can set according to device

capability.

Resolution

The resolution value may vary due to different device capabilities.

Please select from the dropdown list.

Frame rate

The frame rate value may vary due to different device capabilities.

Please select from the dropdown list.

Bit Rate

The default setup is 1024Kb/S. The bit rate value may vary due to

different device capabilities and frame rate setups. Please select

from the dropdown list.

After you enable zero-channel encoding function , click Preview button and then select

split mode

at the right corner of the main interface, system can display

Summary of Contents for NVS0104HDC

























































































































Search results

Summary of Contents for NVS0104HDC

Reviews:

Brands by name

Popular brands

Dahua NVS0104HDC, User Manual

Search results

Summary of Contents for NVS0104HDC

Reviews:

Brands by name

Popular brands