Dahua 1206761 Installation Manual Download Page 8

Page: 8 / 25

SPEED DOME INSTALLATION

1.1

Installation Environments

Basic Requirement



All installation and operation here should conform to your local electrical safety codes.



Before installation, please open the package and check all the components are included.

Please make sure the speed dome installation environment and installation mode can meet

your requirement. If there is special requirement, please contact your local retailer for more

information.



We assume no liability or responsibility for all the fires or electrical shock caused by

improper handling or installation.

1.2

Check installation space and installation location intension

Please make sure the installation environment has enough space to install the speed dome and

its corresponding bracket.

Please make sure the ceiling, wall and the bracket can support the speed dome and its

corresponding installation component. It shall sustain the 8X weight of the speed dome.

1.3

About cable

Please select the cable according to your transmission distance.

The minimum video coaxial-cable requirement is:



75 ohm.



Full cable with copper conductor



95% knitted copper shield



RS485 communication cable, refer to appendix 2

International Model

Max Transmission Distance
(Ft\M)

RG59/U

750Ft (229M)

RG6/U

1,000Ft (305M)

RG11/U

1,500Ft (457M)

Note:

The above can be applied to analog speed dome and network speed dome

International Mode

Max Transmission Distance(Ft\M)

SYV-75-3

720P

（

25fps\30fps)

：

500M/1640Ft

720P

（

50fps\60fps)

：

300M/984Ft

1080P

（

25fps\30fps):300M/984Ft

Note:

The above can be applied to HDCVI speed dome

Summary of Contents for 1206761


























Search results

Summary of Contents for 1206761

Reviews:

Related manuals for 1206761

Brands by name

Popular brands

Dahua 1206761, Installation Manual

Search results

Summary of Contents for 1206761

Reviews:

Related manuals for 1206761

Brands by name

Popular brands