background image

Introduction 

 

The 

CCD-100

 camera system is a fiscally 

responsible approach to any imaging situation.  The 
camera automatically adjusts to any light situation to 
provide clear, crisp images for even the most 
demanding application.  In those times when control is a 
necessity, the camera's automatics can be switched off, 
allowing control of those parameters that are important 
to you. Camera adjustments can also be remote 
controlled using the optional 

RC100 

remote. (P/N 

207672-01). 

The 

CCD-100

 uses the latest in circuitry and design 

to provide images that will dazzle in even the toughest 
light situations.  The camera's automatic controls 
provide exceptional performance from high light levels 
to the dimmest environments.  And if additional 
sensitivity is needed, no problem.  Just attach the 

CCD-

100

 to the Dage 

InvestiGater

 and extend the camera's 

exposure time to whatever is required.  The combination 
of the 

CCD-100

 and 

InvestiGater

 allow a low cost 

alternative to those expensive cameras and frame 
grabbers that deliver only a fraction of the capability at 
a great premium.  And with our Dage-MTI series of 
products, you won't be spending a lot of time setting up 
your system.  That leaves time for what you purchased 
the camera for in the first place; to get the images 
needed to perform your job. 

 

DAGE-MTI

 offers our customers state-of-the-art video 

technology… with an eye on your image.

Summary of Contents for CCD-100

















Reviews: