Daewoo KQG-63N75S Service Manual Download Page 7

6

Connect the mains lead to an electrical outlet.

After placing the food in a suitable utensil, open the oven door and put it on the glass tray. Glass tray must always
be in place during cooking.

Shut the door.
Make sure that it is firmly closed. 

How to set each function
To set MICROWAVE cooking 

• Set the variable power selector to the desired power level.

To set GRILL Cooking

• Set the POWER SELECTOR to the 

(grill) position.

To set COMBI Cooking

• Set the POWER SELECTOR to the 

(combi) position.

Set the time control by turning the timer knob and then microwave cooking starts.
• If turning the timer knob for less than 2 minutes, turn it past 2 minutes and then back to the desired time.
• During the same time, the rotating angle of the timer knob of the period from 60 to 10 minute is smaller than that

of the period from 10 to 0 minute owing to the dual speed of the timer motor.

Microwave energy will be turned off automatically when the timer point to "OFF".
Then take out foods.
• To prevent the oven operating with the door open, your microwave oven is fitted with safety door interlock

switches. If you wish to inspect the food during the cooking time, simply open the door. 

The oven will automatically stop cooking.

To continue cooking, you simply close the door.

• If you wish to stop cooking during the cooking, simply turn the timer knob the point "OFF".

Cooking can be reset at any time during the cooking cycle by only turning the timer knob.

• Do not let the timer continue to operate after removing food.

The safety lock prevents unwanted oven operation such as by small children. To set, pull down the side knob like
the figure.
To cancel, lift up the slide knob.

NOTE : When using the GRILL or COMBI mode;
• Do not open the door so often, the temperature inside the oven decrease and the

cooking may not be completed in setting time.

• Never touch the oven window and metal interior of the oven when taking food in

and out, because the temperature inside the oven and door is very high.

• When using these modes, be careful as the tray will be hot to touch, use oven

gloves or pot holders while handling tray.

1

2

3

4

5

6

7

8

SYMBOL

POWER LEVEL

OUTPUT POWER

WARM

26%

DEFROST

41%

580W

MEDILUM

73%

700W

MED-HIGH

88%

MAX

HIGH

100%

UNLOCK

LOCK

SLIDE

KNOB

OPERATIONS AND FUNCTIONS

Summary of Contents for KQG-63N75S


























Reviews: