background image

2

SAFETY AND PRECAUTIONS

1. FOR SAFE OPERATION

Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may
cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
(Only a trained service personnel should make repairs.)

(1)  A broken door hinge.
(2)  A broken door viewing screen.
(3)  A broken front panel, oven cavity.
(4)  A loosened door lock.
(5)  A broken door lock.

The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven.
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. 
The microwave oven has concealed switches to make sure the power is turned off when the door is opened. 
Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.

2. FOR SAFE SERVICE PROCEDURES

1. If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the

oven.

2. If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the

oven.

(a) inform the manufacturer, importer or assembler,
(b) repair the unit at no cost to the owner,
(c) attempt to ascertain the cause of the excessive leakage,
(d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.

3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact

the manufacturer and the dealer immediately.

IMPORTANT

The wire in this mains lead colored in accordance with the following code.

Green-and-yellow : Earth
Blue

: Neutral

Brown

: Live

As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings iden-
tifying the terminals in your plug, proceed as follows.
The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked with
the letter ‘E’, earth symbol or colored green-and-yellow.
The wire which is colored blue must be connected to the terminal which is marked with the letter ‘N’ or colored
black.
The wire which is colored brown must be connected to the terminal which is marked with the letter ‘L’ or colored
red.

NOTE : 

The oven is designed for counter-top use only.

Summary of Contents for KOR-6Q8G5S


































Reviews: