Daewoo KOR-122M0A Service Manual Download Page 9 | Manualshive

Page: 9 / 58

background image

8

This section includes useful information about oven operation.

1. Plug power supply cord into a standard 3-pronged 20 Amp, 120V AC 60Hz power outlet.
2. After placing the food in a suitable container, open the oven door and put it on the glass tray.

The glass tray and roller guide must always be in place during cooking.

3. Shut the door. Make sure that it is firmly closed.

Wattage output chart

• The power-level is set by pressing the POWER pad. The chart shows the display, the power level and the

percentage of power.

OPERATION PROCEDURE

1. The oven light is on only when the microwave

oven is operating.

2. The oven door can be opened at any time

during operation by touching the door release
button on the control panel the oven will
automatically shut off.

3. Each time a pad is touched, a BEEP will sound

to acknowledge the touch.

4. The oven automatically cooks on full power

unless set to a lower power level.

5. The display will show ": 0" when the oven is

plugged in.

6. Time clock returns to the present time when the

cooking time ends.

7. When the STOP/CLEAR pad is touched during

the oven operation, the oven stops cooking and
all information retained.
To erase all information (except the present
time), touch the STOP/CLEAR pad once more.
If the oven door is opened during the oven
operation, all information is retained.

8. If the START pad is touched and the oven does

not operate, check the area between the door
and door seal for obstructions and make sure
the door is closed securely.
The oven will not start cooking until the door is
completely closed or the program has been
reset.

Make sure the oven is properly installed
and plugged into the electrical outlet.

@@@@@@@@e?

@@@@@@@@e?

@@h?

@@h?

@@h?

@@h?

@@h?

@@h?

@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e

@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e

@@@@@@@@

@@@@@@@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

?@@

?@@

?@@

?@@

?@@

?@@

?@@@@@@@@

?@@@@@@@@

?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@

?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@

@@g

@@g

@@g

@@g

@@g

@@g

@@@@@@@@

@@@@@@@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

@@

Touch POWER pad

Power level (Display)

Approximate Percentage

Once the Touch

of Power

POWER

P-HI

100%

9

P-90

90%

8

P-80

80%

7

P-70

70%

6

P-60

60%

5

P-50

50%

4

P-40

40%

3

P-30

30%

2

P-20

20%

1

P-10

10%

0

P-0

0%

«
...
7
8
9
10
11
...
»

Summary of Contents for KOR-122M0A



























































Reviews:

No comments

Related manuals for KOR-122M0A

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 119

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 30

Brand: Hamilton Beach Pages: 20

Brand: Galanz Pages: 13

Brand: DAEWOO ELECTRONICS Pages: 27

Brand: Russell Hobbs Pages: 32

Brand: Watlow Electric Pages: 23

Brand: Hotpoint Ariston Pages: 84

Brand: Belling Pages: 10

Brand: TAGLIAVINI Pages: 124

7170 052? 7172 042

Brand: Foster Pages: 18

Brand: Gram Pages: 28

Brand: NEFF Pages: 40

CLassic / Professional +Kitchener / Hi-LITE

Brand: Rangemaster Pages: 40

Brand: Lang Pages: 24

Brand: Blodgett Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands