Daewoo KOR-122M0A Service Manual Download Page 17 | Manualshive

Page: 17 / 58

background image

16

Auto cook allows you to cook or reheat many of your favorite foods by repeatedly touching menu pad. After
the menu selections, touch chosen pad until number in display is same as desired quantity to cook.

1. Touch MENU pad.

2. Touch WEIGHT pad.

MORE pad: adds 10 seconds to 20 seconds.
LESS pad: removes 10 seconds to 20 seconds.

This pad only works with one touch cooking.
Always input prior to one touch sequence.

AUTO COOK (MENU & WEIGHT) ; KOR-122M

MORE, LESS

When you touch MENU pad once, “AC-1” is displayed.
The display will then begin blinking. By repeatedly
touching this pad, you can select other food category
as shown in the chart below.

When you touch WEIGHT pad once, “1” is displayed.
After 1.5 seconds, the display changed into cooking
time of quantity and the oven starts cooking.

MENU

WEIGHT

◆

Baked Potato

◆

(5.5 oz ~ 6.5 oz/ea.)

• 1 NO (ea.) : Touch WEIGHT once.
• 2 NO (ea.) : Touch WEIGHT twice within 1.5 seconds.
• 3 NO (ea.) : Touch WEIGHT three times within 1.5 seconds.

◆

Fresh Vegetable

◆

• 8 oz : Touch WEIGHT once.
• 12 oz : Touch WEIGHT twice within 1.5 seconds.

◆

Soup

◆

• 8 oz : Touch WEIGHT once.
• 12 oz : Touch WEIGHT twice within 1.5 seconds.

◆

Fish Fillets

◆

• 0.5 lb : Touch WEIGHT once.
• 1.0 lb : Touch WEIGHT twice within 1.5 seconds.

◆

Meat Loaf

◆

• 0.5 lb : Touch WEIGHT once.
• 1.0 lb : Touch WEIGHT twice within 1.5 seconds.

CATEGORY

AC-1
AC-2
AC-3
AC-4
AC-5

FOOD

Baked potato

Fresh Vegetable

Soup

Fish Fillets

MEeat Loaf

TOUCH PAD

Touch MENU once.

Touch MENU twice.

Touch MENU three times.

Touch MENU four times.

Touch MENU five times.

«
...
15
16
17
18
19
...
»

Summary of Contents for KOR-122M0A



























































Reviews:

No comments

Related manuals for KOR-122M0A

B57CR23 0B Series

Brand: NEFF Pages: 48

Brand: GE Pages: 2

Brand: Bauknecht Pages: 98

Brand: The Fire Brick Pages: 47

Brand: Magic Chef Pages: 17

Brand: Baumatic Pages: 40

Brand: GE Pages: 64

Brand: Kuppersberg Pages: 132

Brand: Smeg Pages: 38

Brand: cecotec Pages: 31

Professional Custom VEDO1302T

Brand: Viking Pages: 6

Brand: Asko Pages: 48

Brand: Hotpoint Pages: 20

Brand: Artusi Pages: 26

Brand: Jenn-Air Pages: 6

Brand: NutriMill Pages: 16

Brand: Daewoo Pages: 31

Brand: Candy Pages: 244

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands