background image

8

once

P-HI

100%

twice

P-90

90%

3 times

P-80

80%

4 times

P-70

70%

5 times

P-60

60%

6 times

P-50

50%

7 times

P-40

40%

8 times

P-30

30%

9 times

P-20

20%

10 times

P-10

10%

11 times

P-00

0%

The oven light is on when the microwave oven is
operating.

The oven door can be opened at any time during
operation by pressing the door release button on the
control panel. The oven will automatically shut off.  

Each time a pad is touched, a BEEP will sound to
acknowledge the touch.

The oven automatically cooks on full power unless set
to a lower power level.

The display will show ":0" when the oven is plugged in.

Time clock returns to the present time when the cooking
time ends.

When the PAUSE/CANCEL pad is touched during the oven
operation, the oven stops cooking and all information retained.
To erase all information (except the present time), touch the
PAUSE/CANCEL pad once more. If the oven door is opened
during the oven operation, all information is retained.

If the START/EXPRESS COOK pad is touched and the
oven does not operate, check the area between the door
and door seal for obstructions and make sure the door is
closed securely.
The oven will not start cooking until the door is completely
closed or the program has been reset.

This section includes useful information about microwave oven operation.
1. Plug power supply cord into a standard 3- pronged 20Amp, 120V AC 60Hz power outlet.
2. After placing the food in a suitable container, open the oven door and put it on the glass tray.

The glass tray and roller guide must always be in place during cooking.

3. Shut the door. Make sure that it is firmly closed.

1

2

3

4

5

6

7

8

WATTAGE OUTPUT CHART

• The power-level is set by touching the POWER LEVEL pad. The chart shows the display, the power level and the

percentage of power.

Touch POWER pad

Power Level (Display)

Approximate Percentage of Power

OPERATION PROCEDURE(MICROWAVE OVEN)

Make sure the oven is properly installed and plugged
into the electrical outlet.

Touch the PAUSE/CANCEL pad for microwave oven
control part. 
During operation of the microwave oven, pads for
pizza oven control part do not work.

Summary of Contents for KOD-135P9A






































Reviews: