EN
3
6. STORAGE
1) To ensure that the battery is fully charged, avoid setting SS3S in extremely hot or cold environ-
ments.
2) If the equipment will not be used for a long time, please remove the battery before storage.
3) The batteries and chargers must be placed in the instrument box to prevent heat, dust and mois-
ture from entering, check if the switch is off.
4) Check the switch if close or not.
5) The battery should be stored in a dry environment under:
6) Short term less than 1 month storage temperature -20T-4-60X.
7) Short-term storage temperature less than 6 months -10 t ~+35" C.
8) Recommended storage temperature (TC ~3(rc) for longer storage time.
9) The distance between the battery and the combustible must be kept beyond 1.5 m.
• To ensure the service life of the equipment and prevent its degradation, store it in a fully charged
state. When not in use, charge and discharge the battery at least once a month.
Do not turn on the power switch when storing.
7. TECHNICAL SPECIFICATIONS
Power:
18 V
No load speed:
3000 rpm
Linear speed:
5 m/s
Cutting capacity:
80-90 mm
Bar length:
4”/102 mm
Chain pitch:
1/4”
Teeth:
28
Weight:
1 kg
*Battery and charger are not included.
8. EXPLODED VIEW
5. OPERATING INSTRUCTIONS
Please wear suitable clothing and work gloves when using this parent. Before each use, make sure
the belt is running normally. start/off switch and safety switch must be available for normal
use.When loosening the start switch, the power must be turned off. If the switch is damaged, stop
using the device Make sure the voltage of the power supply is consistent with the voltage on
the nameplate. The risk of injury can be reduced by wearing protective devices and ensuring that
the devices are functioning properly.
Confirm the frequency of the operation to ensure that the operation is in the best condition.
• In order to save the use of electric batteries and ensure the best service life of pruning and shea-
ring, do not allow this load of overloaded lice to cut wet and dry branches over 60mm diameter and
20mm.
• When cutting the knife edge mode to stop the operation, turn off the power switch and splash
down the battery box.
Skills
1) When the device is running, say your other hand is at least 15cm away from the cutting area of the
blade, and the hand must not be put into the knife edge.
2) Do not use this equipment to force the bigger branches, otherwise it may make the blade deform
and make the pruning stick.
4) In cold or humid weather, to protect the battery pack, put it under waterproof clothing, do not use
this equipment in rainy days.
5) We recommend that after daily use, the connection between the pruning number and the battery
pack must be cut, and the power switch (8) is closed and put together into the matching tool box.
6) If the user feels the electricity is not enough or the cutting is not smooth enough, check if the
electricity is exhausted or the blade is dull
Cleaning and maintenance
Repair functions not mentioned herein shall be performed by the Service Centre. To ensure the
safety of use, only the original parts can be used.
Repair work functions not mentioned in this specification are performed by the service center. To
ensure safe use, only original parts can be used.
Please close the equipment before starting the chair repair. Clear the connection between the
battery and the plant and store the battery in a safe package.
Wear hand care when touching safety blades. This can avoid sharp blade scratching the user.
Follow-up cleaning and maintenance must be carried out regularly. This ensures long-term and
reliable operation of the equipment.
Clearness
Do not spray the equipment with water or break it into the water, otherwise, it may cause electric shock.
Keep the ventilator, motor room and equipment handle clean. Use a damp cloth or brush cleaner.
Do not use a bay cleaner. Otherwise, it may cause permanent saka failure of the equipment. Please
clean the blade carefully after each use.
Use oily cloth to wipe the blade and absorb the metal to protect the fog.
After 8 hours of continuous operation, please remove the debris such as dust from the front turbu-
lent cover plate of the equipment
• Before charging, check that the surface of the battery is clean and dry.
• Before delivery, the battery of this product is not fully charged. Therefore, before the first use, it
must be sufficient electricity.
• Do not charge the battery for long periods of time, and do not run out of all the power in the soap
tank, otherwise it will damage the battery.
• The Essential Security Department does not include failure due to incorrect use.
• If the battery with sufficient electricity is significantly shorter, it must be replaced if the battery is
exhausted.
• The user can only use the battery pack manufactured by the original equipment operated by the
customer center.
Always keep in mind applicable safety instructions and protection requirements and
environmental information
1) Put the charger in the room b10 and +22M, and stops moisture entering.
2) Check that the switch is in off position.
3) Connect the charger to the corresponding connector for the battery pack.
4) Make sure the power is consistent with the rated values on the charger and adapter.
5) When the red light is on the charger, it indicates that the battery is charging, and the green light
indicates that the charge is completed. The average charge time is 2 hours.
6) When charging is complete, drive the connector from the power source and then cut off the
connector and battery connection.
7) The battery is used to ensure that it is recharged at least once every three months.
Maintain charging temperature 0-C-45-C for soap charger and battery pack, discharge temperature
-1-CTC for battery pack ~60°C
The chain must be stuck to the sprocket. After installation, please check it again.
3. CONTAINS ITEMS
Say carefully open the package, check whether the components are all:
1. Lithium mini chainsaw.
2. Instruction manual and warranty card.
4. CHARING THE BATTERY
Do not expose the battery to extreme conditions such as high temperature or shock. Otherwise, it
will cause personal injury due to the leakage of the electrolytic solution.
Safety bezel
LED light
Lock buttom
Comfortable handle
High-power battery
High quality chain
Guide plate
Switch button
2. Install the chine guide
First load the chain into the guide plate, and the middle guide tooth just sticks into the guide plate
guide slot.Note: the chain blade should be forward.
NOTE:
The charging chainsaw has a device to adjust the tensioning of the chain. When installing the
guide plate, make sure that the adjusting block gets stuck into the positioning adjusting hole at the
end of the guide plate!
Put the chain into the guide plate.
Note the direction of the cutting teeth.
Align the pin hole and install the reverse hole and chain.
Intall the side cover and tighten the screw nut.
3. How to adjust the tightness of the chain?
The adjustment standard is to lift the chain in the middle of the guide plate by hand and expose 1-3
middle guide teeth.
Loosen the compression nut.
As shown in the picture, twisted the adjusting screw clockwise to tension the chain, countercloc-
kwise is for loosening.
The chain tightness is shown as below.
NOTE:
1-3 middle guide teeth are exposed in the pull-down chain.
The new chain will be stretched in the early stage of use. Please check and adjust to the appropriate
tension frequently,because the loose chain is easy to derail, which may lead to rapid wear of the
chain and guide plate.
1. FUNCTION DESCRIPTION
Loosen the nut counter clockwise and remove the side cover.
2. OPERATING INSTRUCTION
1. Remove chain
How to remove chain, loosen compression button,remove the side cover. After remove the side
cover as picture ,remove the guide directly
Wrench
