3. DISPLAY and KEY operation
1)DISPLAY :
4½ Digit LED
* Key operation start : press to
key.
Key operation exit : press to
key.
* Display : setting mode and operation mode.
1. Setting mode : data confirmation or correction.
2. Operation mode : normal operation state.
3. Press to
key : setting mode.
Press to
key : operation mode.
2) L.E.D Display
LED state
Description
HI
operation
Display operation mode of high relay.
setting
Confirm and adjust high data
LO
operation
Display operation mode of low relay.
setting
Confirm and adjust low data
FS
setting
Confirm and adjust full scale data.
Input the full range or capacity of sensor.
DP
setting
Confirm and adjust decimal point.
CAL
setting
key in sensor output data ( mV/V )
* refer to 6 - 1)
FS+
CAL
setting
auto calibration execution mode.
cal data is adjusted automatically.
* refer to 3 - 6)
F S +
DP
setting
Adjust display time and unit of
measurement data
* refer to 6 - 2)
DP+
CAL
setting
Software adjustment mode.
* refer to 6 - 3)
F S +
DP+
CAL
operation
Set or reset data lock mode
* refer to 3 - 4)
3) KEY operation
Mode
select
1. HI
LO
FS
DP
CAL
FS+CAL
FS+
→
→
→
→
→
→
DP
DP+CAL
→
2. All FND of selected mode will blink.
Positio
n
select
3. Press key : 10000→1000→100→10→1
Selected digit position will blink
4. DP(decimal point mode) : decimal point
position movement key.
10.000
100.00
1000.0
10000
→
→
→
Number
select
5. Data correction key.
6. 5 digit
1, -1, -, non
→
7. The others 1
2
3
4
5
6
7
8
9
→ → → → → → → →
0
→
Input
8. Input data. After setting up must press
key therefore become input.
A u t o
zero
9. Sensor : No load state(0V, 4
)
㎃
10. Display : 0
Key result
Description
＋
Lock
mode
11. Protect setting data.
12. Reset lock mode to adjust data
4) PROTECTION mode
Use this mode for protection and security of System.
high, low data is possible to adjust irrespectively.
Mode
confirm and setting
Unlock
* Press
and
key during 5 sec at the same
time
FS, DP, CAL LED will light up and reset lock mode
(data correction enable)
Lock
* Press
and
key during 5 sec at the same
time in unlock mode : FS, DP, CAL LED turn off
(lock mode)
* power off : Set lock mode automatically.
5) AUTO ZERO mode
Initialize sensor and indicator.
Execute this mode at unlock mode.
Execution process (display : operation mode)
(1) Sensor : no load.
(2) Voluntary data display.
(3) Press
key and
key at the same time.
Zero display (ex : 0, 0.0, 0.00, 0.000)
(4) This data is memorized to indicator though power turn off.
(5) If operate mode with input signal to remain, this point is
memorized zero point.
6) AUTO CALIBRATION mode
Convenience to use when do not know calibration data of
sensor or displayed the measurement value differently.
EX)
At sensor Supply : 100.00 kg/㎠
Display
: 100.05 or 99.05 kg/㎠
Adjustment
: 100.00 kg/㎠
(1) Adjust zero point of indicator.
(2) Apply known load to sensor. Large load is high safety.
(3) Press
key : F.S and CAL L.E.D turn on at the same
time.
(4) As example table, 100.05 or 99.05 will blink.
(5) After correction of 100.00 using
key and
key,
press
key.
(6) 100.05 is display correction of 100.00.
(7) At this time, cal data is corrected minutely.
(8) If corrected cal data is over limits of 2-4), correct of DIP
S/W setting and again set the auto calibration.
4. Operating flow chart
Install and connection --Mount indicator to panel and make
connection. (Check AC POWER 110/220V)
Unlock mode -- Press
＋
key(data protection unlock)
DATA Input
-- Set data(high, low, F.S, DP, CAL),
refer to 6
DIP S/W setting --sensor output data ---DIP S/W 1, 2, 3, 4
analog output
---- DIP S/W 5
filter frequency
---- DIP S/W 6, 7, 8
Auto zero
-- Sensor : no load
Press
＋
key (auto zero)
AUTO CAL
-- Execute auto calibration.
Mode Check
-- Check function(Relay output,analog output,
reset, hold, peak).
Lock mode setting --Press
＋
key(data protection mode)
