background image

VS Recorder – Direct-wired Stations/Setup

 

 

Pg. 9                                                                                                                                  

visit us online @ www.

dacsolution.com 

Direct-wired Telephony Stations

    

                                                               

 

 

Direct-wired  telephony  stations  provide  additional  features  to  VS  Recorder  and  do  not  require  a 

dedicated telephone line. This works by running dedicated wires from VS Recorder to the telephony station. 
In addition, a junction box will be needed to interface between the station and the VS Recorder voice card. 

 
 

- What You Will Need 

 

 

A DAC digital dictate station of your choice 

 

A DAC junction box 

 

Cat3 ribbon cable to run from the station to the VS Recorder voice card 

 

 

- Setup 

 
 

The following steps presume you have already completed the basic installation of VS Recorder. 

 

Step 1. 

Plug your dictate station’s A/C adapter in. 

 

Step  2. 

You  may  use  either  an  ordinary  telephone  cable  or  make  a  custom  one,  preferably  with  Cat3 

ribbon  cable.  Only  1  pair  (the  2  middle  wires)  will  be  used.  Plug  the  cable  into  the 

Data

  jack  on  the 

dictate station. 
 

Step 3. 

Run the other end of the cable to your junction box. Plug the cable into the 

Station 1

 jack. This 

will directly wire the station to VS Recorder’s Channel 1. 

 

Step  4. 

Run  a  telephone  cable  (single  or  double  pair  –  doesn't  matter)  from  the 

Port  1

  jack  on  the 

junction box to the 

Line 1

 jack on the VS Recorder voice card. 

 

Step 5. 

Verify that the switch for 

Station 1

 on the front of the junction box is set to 

Loop

 

Step 6. 

Plug the junction box's A/C adapter in. 

Summary of Contents for VS Recorder













Reviews: