manualshive.com logo in svg

Da-Lite Curved Multi Format Imager, Instruction Book, Page: 13 / 16

Share
Download
Da-Lite Curved Multi Format Imager Instruction Book Download Page 13

13

Symptom

Cause

Solution

 Masking System will not operate. 
Motor does not hum.

Incorrect line voltage.

Verify 115-125V (or 220-240V). If insufficient voltage, 
rewire incoming electric line.

Blown fuse.

Replace fuse.

Tripped circuit breaker.

Reset circuit breaker.

No power to junction.

Check above. Tighten all loose wire connections. Correct 
any improper connections. 

Check for power across black and white leads.

Screen will not operate  
and motor does not hum.

Power at junction box.

Thermal overload tripped.

Let motor cool down for 30 minutes. Try again.

Defective motor, limit switch or capacitor.

Replace motor assembly.  
NOTE: Motor is a sealed assembly.

Capacitor burned out.

Replace motor assembly.

Masking System does not stop at 
correct position.

Limit switch out of adjustment.

See Limit Travel Adjustment section.

 Noise. 
 NOTE: Masking Systems will operate  
with a low pitched hum.

 Squeaking, rubber end plug rubbing on motor.

Center roller in case.

 Grinding. Foreign object in screen rubbing on 
roller or fabric.

Remove.

Gear noise.

Replace motor assembly.

 Coasting.

 Defective  brake.

Replace motor assembly.

  Fabric  hangs  crooked.

Masking System not installed properly.

 Check for level and plumb.

Mask is damaged.

Replace fabric.

Troubleshooting

Visit www.da  -lite.com/products/product_videos.php to find 
installation and troubleshooting videos and tutorials. You will also 
find a link to Live Chat for interactive support and you can contact 

us by email at [email protected] or by phone at (800) 622-3737 or 
(574) 267-8101 with any troubleshooting questions.

Summary of Contents for Curved Multi Format Imager

















Reviews:

No comments