D.W. Fearn VNE Operating Instructions Manual Download Page 12 | Manualshive

Page: 12 / 21

D.W. Fearn VNE Operating Instructions Manual Download Page 12

VNE Vacuum Tube Compression Amplifier

HAZELRIGG INDUSTRIES

12

OPERATION

Input

Since the input cable will be carrying high quality audio, it is important that a well-shielded cable
is used. You should strive to minimize the number connectors, patch jacks, switches, etc. between
the source and the VNE input.

Output

The output of the VNE is line level, transformer balanced. Note that vacuum tube equipment is
more  sensitive  to  load  impedance  than  solid  state  units.  The  VNE  design  was  optimized  for
feeding  a  balanced  bridging  input  (20k  ohms  or  greater).  When  feeding  a  600  ohm  load,  there
may be a slight degradation of some of the specifications. In modern studio equipment, bridging
line inputs are universal. If the device being fed by the VNE has an input termination switch, that
switch should be in the “off” position.

The VNE can feed balanced or unbalanced inputs with no need for any modification in output
wiring. Either pin 2 or 3 can be grounded, although pin 2 is normally used as the ”hot” and pin 3
grounded in unbalanced configurations.

«
...
10
11
12
13
14
...
»

Summary of Contents for VNE






















Reviews:

No comments