D-Link DVG-2101sp User Manual Download Page 7

Page: 7 / 57

DVG-2101SP User Manual

Front Panel

Power LED

This LED will light solid when the

device finishes a self-test and

booting up. This LED will flash

during device self-test and booting

and light off if the self-test fails.

Phone LED

This LED will light solid when the

telephone is off-hook. A fast blinking

LED indicates an incoming call and

a slow blinking LED indicates a

message is waiting. This LED will

light off if the phone connected to

the phone port is on-hook.

WAN LED

This LED will light solid when a connection

is established and blink to indicate activity.

If this LED does not light up when a cable is

connected, verify the cable connections and

make sure your devices are powered on.

Register LED

This LED will light solid if the phone

account registers successfully. This

LED will flash during registering and

light off if registering fails.

Provision LED

This LED will light up solid if the

device provisions successfully. The

LED will flash during provisioning

and will be off if provisioning fails.

Line LED

This LED will light solid when

a connection is established

and blink to indicate activity.

Summary of Contents for DVG-2101sp





















































Search results

Summary of Contents for DVG-2101sp

Reviews:

Related manuals for DVG-2101sp

Brands by name

Popular brands

D-Link DVG-2101sp, User Manual

Search results

Summary of Contents for DVG-2101sp

Reviews:

Related manuals for DVG-2101sp

Brands by name

Popular brands