D-Link DVG-2101sp User Manual Download Page 11

Page: 11 / 57

DVG-2101SP User Manual

Click

Set your PC’s IP address to

192.168.1.1 and the subnet mask to

255.255.255.0. The default gateway

and primary DNS server IP addresses

should be the LAN IP address of the

DVG-2101SP (192.168.1.150).

Open your Web browser and

type http://192.168.1.150 into

the URL address box. Press the

Enter or Return key.

Configuration

Prior to using your Web Browser for accessing the web-based configuration utility, if DHCP is not enabled on

your network, be sure to assign a static IP address to the VoIP Telephone Adapter.

Use the computer that was last connected directly to your Cable/DSL modem. Right-click

My Network Places

> select

Properties

> right-click

Local Area Connection

> select

Properties

> double-click

Internet Protocol

(TCP/IP)

In order to use a web browser to configure the VoIP Adapter you must make sure it has a valid Ethernet

connection to a PC or LAN via its LAN port. Access the configuration utility to check the LAN port by entering

the IP Address into your web browser address field.

When you first log in, enter

the Username “

admin

” and

leave the Password blank.

These may be changed later.

Click the

Login

button.

Summary of Contents for DVG-2101sp





















































Search results

Summary of Contents for DVG-2101sp

Reviews:

Related manuals for DVG-2101sp

Brands by name

Popular brands

D-Link DVG-2101sp, User Manual

Search results

Summary of Contents for DVG-2101sp

Reviews:

Related manuals for DVG-2101sp

Brands by name

Popular brands