D-Link DSL-2650NRU User Manual Download Page 102

Page: 102 / 107

DSL-2650U/NRU

3G/ADSL/Ethernet Router

with Wi-Fi and Built-in Switch

User Manual

Configuring via Web-based Interface

Firmware Upgrade

On the

System / Firmware upgrade

page, you can upgrade the firmware of the router.

Upgrade the firmware only when the router is connected to your PC via a wired
connection.

Figure 81. The

System / Firmware upgrade

page.

The current version of the router's firmware is displayed in the

Firmware version

field on the

Start

page. If you need to install a newer version of the firmware, follow the next steps:

Attention! Do not turn off the router before the firmware upgrade is completed. This may
cause the device breakdown.

1. Download a new version of the firmware from

www.dlink.ru

2. Click the

Choose/Browse

button on the

System / Firmware upgrade

page to locate

the new firmware file.

3. Click the

Update

button to upgrade the firmware of the router.

4. Wait until the router is rebooted (about one and a half or two minutes).

5. Log into the web-based interface using the login (

admin

) and the current password.

6. Select the

Factory

line in the top-page menu displayed when the mouse pointer is over the

System

caption.

4 The name of the button depends upon the web browser that you use.

Page

102

of 107

Summary of Contents for DSL-2650NRU












































































































Search results

Summary of Contents for DSL-2650NRU

Reviews:

Brands by name

Popular brands

D-Link DSL-2650NRU, User Manual

Search results

Summary of Contents for DSL-2650NRU

Reviews:

Brands by name

Popular brands