D-Link DIR-320 User Manual Download Page 143

Page: 143 / 220

DIR-320

Wireless N150 Router with 3G/CDMA/LTE Support

and USB Port

User Manual

Configuring via Web-based Interface

To activate the WPS function, select the

WPS Enable

checkbox and click the

Apply

button. When

the checkbox is selected, the

Information

and

Connection

sections are available on the page.

Parameter

Description

Default PIN code

The PIN code of the router. This parameter is used when connecting
the router to a registrar to set the parameters of the WPS function.

WPS Status

The state of the WPS function:

•

Configured

(all needed settings are specified; these settings

will be used upon establishing the wireless connection)

•

Unconfigured

(after activating the WPS function, the SSID

and the encryption key will be configured automatically, the
network authentication type will be changed to WPA2-PSK).

SSID

The name of the router's WLAN.

Network Authentication

The network authentication type specified for the WLAN.

Encryption

The encryption type specified for the WLAN.

Encryption key

The encryption key specified for the WLAN.

Refresh

Click the button to refresh the data on the page.

Reset to unconfigured

Click the button to reset the parameters of the WPS function.

WPS Method

A method of the WPS function. Select a value from the drop-down
list.

PIN

: Connecting the device via the PIN code.

PBC

: Connecting the device via the push button (actual or virtual).

PIN Code

The PIN code of the WPS-enabled device that needs to be connected
to the wireless network of the router.
The field is displayed only when the

PIN

value is selected from the

WPS Method

drop-down list.

Connect

Click the button to connect the wireless device to the router's WLAN
via the WPS function.

Page

143

of 220

Summary of Contents for DIR-320





























































































































































































































Search results

Summary of Contents for DIR-320

Reviews:

Related manuals for DIR-320

Brands by name

Popular brands

D-Link DIR-320, User Manual

Search results

Summary of Contents for DIR-320

Reviews:

Related manuals for DIR-320

Brands by name

Popular brands