D-Link DGS-1510-20 Hardware Installation Manual Download

Page: 46 / 69

DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide

Feature

Detailed Description

•

DEM-310GT (1000BASE-LX, Single-mode, 10 km)

•

DEM-311GT (1000BASE-SX, Multi -mode, 550 m)

•

DEM-312GT2 (1000BASE-SX, Multi-mode, 2 km)

•

DEM-314GT (1000BASE-LHX, Single-mode, 50 km)

•

DEM-315GT (1000BASE-ZX, Single-mode, 80 km)

•

DGS-712 (1000BASE-TX)

Supports to following WDM transceivers:

•

DEM-302S-BXD/BCU (1000BASE-BX, Single-mode, 2 km)

•

DEM-330T/R (1000BASE-BX, Single-Mode, 10 km)

•

DEM-331T/R (1000BASE-BX, Single-Mode, 40 km)

SFP+ Ports

Compliant with the following standards:

•

IEEE 802.3ae compliance

•

IEEE 802.3z compliance

Supports to following SFP/WDM transceivers:

•

All supported SFP/WDM transceivers will work in SFP+ ports

Supports to following SFP+ transceivers:

•

DEM-431XT-DD (10GBASE-SR SFP+ Transceiver, 80 m:

OM1 & OM2 MMF 300 m: OM3 MMF)

•

DEM-431XT (10GBASE-SR SFP+ Transceiver (w/o DDM), 80

m: OM1 & OM2 MMF 300 m: OM3 MMF)

•

DEM-432XT-DD (10GBASE-LR SFP+ Transceiver, 10 km)

•

DEM-432XT (10GBASE-LR SFP+ Transceiver (w/o DDM), 10

km)

•

DEM-433XT-DD (10GBASE-ER SFP+ Transceiver, 40 km)

•

DEM-433XT (10GBASE-ER SFP+ Transceiver (w/o DDM), 40

km)

•

DEM-434XT (10GBASE-ZR SFP+ Transceiver (w/o DDM), 80

km)

•

DEM-436XT-BXU (10GBASE-LR BiDi SFP+ Transceiver (w/o

DDM), 20 km, TX: 1270 nm, RX: 1330 nm)

•

DEM-436XT-BXD (10GBASE-LR BiDi SFP+ Transceiver (w/o

DDM), 20 km, TX: 1330 nm, RX: 1270 nm)

Supports to following SFP+ Direct Attached Cables (DAC):

•

DEM-CB100S-10-GbE (SFP+, 1 m, Direct Attach Cable), for

stacking

•

DEM-CB300S-10-GbE (SFP+, 3 m Direct Attach Cable), for

stacking

•

DEM-CB700S-10-GbE (SFP+, 7 m Direct Attach Cable), for

stacking

PoE Ports

(DGS-1510-28P, DGS-1510-
28XMP, and DGS-1510-
52XMP Only)

Supports the following:

•

IEEE 802.3af PoE and IEEE 802.3at PoE+ compliance

•

Power (ports 1 to 24) to PD devices up to 15.4 Watt per port

(802.3af) or 30 Watt per port (802.3at) and more sufficiently is
able to provide power to PD devices

•

The auto-discovery feature automatically recognizes the

connection of the PD device and immediately provides power

•

Automatically disable ports if the port current is over 600mA

while. Other ports will remain active

•

Active circuit protection automatically disables the port if there

is a short while other ports remain active

Summary of Contents for DGS-1510-20






































































Search results

Summary of Contents for DGS-1510-20

Reviews:

Related manuals for DGS-1510-20

Brands by name

Popular brands

D-Link DGS-1510-20, Hardware Installation Manual

Search results

Summary of Contents for DGS-1510-20

Reviews:

Related manuals for DGS-1510-20

Brands by name

Popular brands