D-Link DGS-1510-20 Hardware Installation Manual Download

Page: 40 / 69

DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide

Appendix A – Technical Specifications

General

Feature

Detailed Description

Standards

IEEE 802.1AB Link Layer Discovery Protocol

IEEE 802.1D-2004 Spanning Tree Protocol

IEEE 802.1p Priority Queues

IEEE 802.1Q-2005 Virtual LAN

IEEE 802.1S Multiple Spanning Tree Protocol

IEEE 802.1W Rapid Spanning Tree Protocol

IEEE 802.1X Port-based Authentication

IEEE 802.3i 10BASE-T Ethernet

IEEE 802.3u 100BASE-TX Fast Ethernet

IEEE 802.3ab 1000BASE-T Gigabit Ethernet

IEEE 802.3ad Link Aggregation

IEEE 802.3ae 10GBASE-X/10GBASE-R/10GBASE-W

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet

IEEE 802.1az Energy-Efficient Ethernet

IEEE 802.3x Flow Control support for Full-Duplex mode

IEEE 802.3z 1000BASE-T Gigabit Ethernet

Data Transfer Rates

Half-duplex

Full-duplex

Ethernet

10 Mbps

20 Mbps

Fast Ethernet

100 Mbps

200 Mbps

Gigabit Ethernet

2 Gbps

10 Gigabit Ethernet

20 Gbps

Stacking Topology

Duplex Ring, Duplex Chain

Network Cables

UTP/STP Category 3, 4, 5 for 10BASE-T

UTP/STP Category 5 Enhanced for 1000BASE-T

UTP/STP Category.5, 5 Enhanced for 100BASE-TX

EIA/TIA-568 100

Ω screened twisted-pair (STP) (100m)

Physical and Environmental

Feature

Detailed Description

Internal Power Supply

DGS-1510-20:

100-240 VAC, 50/60 Hz, 24 Watt

DGS-1510-28:

100-240 VAC, 50/60 Hz, 30 Watt

DGS-1510-28P:

100-240 VAC, 50/60 Hz, 253 Watt

DGS-1510-28X:

100-240 VAC, 50/60 Hz, 30 Watt

DGS-1510-28XMP:

100-240 VAC, 50/60 Hz, 430 Watt

DGS-1510-52:

100-240 VAC, 50/60 Hz, 54 Watt

DGS-1510-52X
(HW: A1):

100-240 VAC, 50/60 Hz, 54 Watt

Summary of Contents for DGS-1510-20






































































Search results

Summary of Contents for DGS-1510-20

Reviews:

Related manuals for DGS-1510-20

Brands by name

Popular brands

D-Link DGS-1510-20, Hardware Installation Manual

Search results

Summary of Contents for DGS-1510-20

Reviews:

Related manuals for DGS-1510-20

Brands by name

Popular brands