D-Link DGS-1510-20 Hardware Installation Manual Download

Page: 27 / 69

DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide

Installing the RPS into a Rack-mount Chassis

The DPS-700 is a redundant power supply unit designed to conform to the voltage requirements of
the switches being supported.

The DPS-700 can only be used with the DGS-1510-52XMP.

CAUTION:

DO NOT connect the RPS to AC power before the DC power cable is

connected. This might damage the internal power supply.

DPS-700

The DPS-700 is connected to the Master Switch using a 22-pin DC power cable. A standard, three-
pronged AC power cable connects the redundant power supply to the main power source.

Figure 2-10 Front view of the DPS-700

1. Insert one end of the 22-pin DC power cable into the receptacle on the Switch and the other end into the

Redundant Power Supply unit.

2. Using a standard AC power cable, connect the redundant power supply to the main AC power source. A

green LED on the front of the DPS-700 will glow to indicate a successful connection.

3. Re-connect the Switch to the AC power source. The LED indicator will show that a redundant power supply is

now in operation.

4. No configuration in the Switch’s firmware is needed for this installation.

NOTE:

See the RPS Quick Installation Guide for more information.

Summary of Contents for DGS-1510-20






































































Search results

Summary of Contents for DGS-1510-20

Reviews:

Related manuals for DGS-1510-20

Brands by name

Popular brands

D-Link DGS-1510-20, Hardware Installation Manual

Search results

Summary of Contents for DGS-1510-20

Reviews:

Related manuals for DGS-1510-20

Brands by name

Popular brands