background image

6/20

RZN 4402/04-K

Rev.:3.8

Mounting of housing 2

Mount control panel sheltered and easily
accessible for maintenance in proximity of
drive

Surface mounting:

1. Remove cable cover
2. Fasten housing trough with 4 screws at

wall

Flush mounting

(not hollow wall mounting):

1. Screw down wall hook and plaster cross

at housing trough

2. Fasten housing trough in niche and

remove plaster cross again after
plastering

Attention: Fire resistance category of fire
walls must not be inadmissibly influenced.
Sound insulation is impaired by flush
mounting.

Final mounting:

3. Mount and connect central pcb
4. Screw down cable cover
5. Unhinge door of the door frame (for this,

press joint rod upwards using pliers).

Fasten door frame on housing trough, and
hang door on it’s hinges again

Piktograph explanation

Smoke and heat vent alarm

Control panel O.K.

Fuse actuator

Mains existing

Vent button function "ON"

Vent button function "OFF"

Charging voltage controller

Battery

Fastening of accumulators

Only RZN 4404-K.

Covering

Place enclosed covering cap over supply
terminal after mains cable has been connected.

Summary of Contents for RZN 4402-K





















Reviews: