Cypress Semiconductor CY7C1310AV18 Specification Sheet Download Page 18

Page: 18 / 21

CY7C1310AV18

CY7C1312AV18

CY7C1314AV18

PRELIMINARY

Document #: 38-05497 Rev. *A

Page 18 of 21

Identification Register Definitions

Instruction Field

CY7C1310AV18

CY7C1312AV18

CY7C1314AV18

Description

2M x 8

1M x 18

512K x 36

Revision Number (31:29)

000

Version number.

Cypress Device ID (28:12) 11010011010000101 11010011010010101 11010011010100101 Defines the type of SRAM.
Cypress JEDEC ID (11:1)

00000110100

Allows unique identification of

SRAM vendor.

ID Register Presence (0)

Indicates the presence of an

ID register.

Scan Register Sizes

Register Name

Bit Size

Instruction

Bypass

Boundary Scan

107

Instruction Codes

Instruction

Code

Description

EXTEST

000

Captures the Input/Output ring contents.

IDCODE

001

Loads the ID register with the vendor ID code and places the register between TDI and TDO.

This operation does not affect SRAM operation.

SAMPLE Z

010

Captures the Input/Output contents. Places the boundary scan register between TDI and

TDO. Forces all SRAM output drivers to a High-Z state.

RESERVED

011

Do Not Use: This instruction is reserved for future use.

SAMPLE/PRELOAD

100

Captures the Input/Output ring contents. Places the boundary scan register between TDI and

TDO. Does not affect the SRAM operation.

RESERVED

101

Do Not Use: This instruction is reserved for future use.

RESERVED

110

Do Not Use: This instruction is reserved for future use.

BYPASS

111

Places the bypass register between TDI and TDO. This operation does not affect SRAM

operation.

Boundary Scan Order

Bit #

Bump ID

11P

10P

10N

10M

11N

11L

11M

10L

11K

10K

10J

11J

11H

10G

Boundary Scan Order

(continued)

Bit #

Bump ID

[+] Feedback

Summary of Contents for CY7C1310AV18






















Search results

Summary of Contents for CY7C1310AV18

Reviews:

Related manuals for CY7C1310AV18

Brands by name

Popular brands

Cypress Semiconductor CY7C1310AV18, Specification Sheet

Search results

Summary of Contents for CY7C1310AV18

Reviews:

Related manuals for CY7C1310AV18

Brands by name

Popular brands