background image

Cybex Eagle 11120 Standing Calf Owner’s Manual

Assembly
Page 4-2

With an assistant, carefully remove the nine Button Head 

B. 

Socket Cap Screws (BHSCS) securing the two halves of 
the frame. See Figure 1.

Carefully move each half through the door-way to the 

C. 

desired location.

With an assistant, carefully attach each half together 

D. 

using the nine BHSCS removed in step 4B. See Figure 1.

Continue on with step 5B.

E. 

5.  

Remove shipping feet and remove the back shrouds.

Carefully remove each (standard) cone-shaped 

A. 

shipping support (using a 3/4” socket or wrench).

Carefully place rubber feet (supplied with machine) 

B. 

on each foot of the frame.

Cut shipping tie securing top weight.

C. 

Lift top weight and turn the Increment Weight Adjusting 

D. 

Knob to select all 15 lbs.(three increment weights each 
side).

Remove the three Phillips head screws securing the 

E. 

top (back) shroud and carefully remove the shroud. 
See Figure 2.

Loosen bottom two screws shown in Figure 3. 

F. 

NOTE: Do not remove the bottom two screws.

Remove the top two screws securing the back shroud 

G. 

assembly. See Figure 4.

Carefully slide rear shroud assembly upward and remove.

H. 

6.  Install the weight stack.

Note how the increment weights are installed.

A. 

With an assistant holding the increment weights, move 

B. 

the adjusting knob to 0 lbs. and remove all six increment 
weights (three each side).

Using an external snap ring pliers, remove the upper 

C. 

snap ring from one of the guide rods and carefully 
lower the guide rod. See Figure 5.

Remove lower snap ring and wave washer from the 

D. 

guide rod. Repeat steps 6C and 6D to remove both 
snap rings from other guide rod.

If possible, lean guide rods outward, away from machine 

E. 

in order to provide the most room for installing weight 
plates.  

Slide top weight up and out of machine and carefully 

F. 

set it aside.

Figure 2

Phillips Head
Screw (3)

Figure 3

Figure 4

Screw

Screw

Figure 5

Upper snap ring

Lower snap ring

Frame

Guide rod 

Wave washer

Figure 1

BHSCS (3)

BHSCS (3)

Locknut (3)

Locknut (3)

BHSCS (2)

Locknut (2)

BHSCS (1)

Locknut (1)

Summary of Contents for Eagle 11120 Standing Calf

































Reviews: