background image

 23

Cybex 18030 Bravo Lift Owner’s Manual

 CAUTION:  Personal injury or property damage may occur if the following precautions 

are not followed. Do not use if less than 1/8” of material remains to the edge. 

Replace all worn handles immediately. Failure to replace worn handles can 

result in injury or property damage.

Inspect bars and handles for wear, paying particular attention to tab area connection points.

 

Attachment 

Hole

Replace bar if less 

than 1/8” of material  

remains to the edge.

 

Inspection

Action

Inspect bars and handles for wear, paying 

particular attention to tab area connection points. Replace all worn handles immediately

.

Inspect snap links for proper latching (indicates 

wear).

Replace all loose or worn grips immediately.

Inspect all labeling for readability, including 

instructional placards, warning and caution 

decals.

Replace all worn labeling immediately.

Inspect all weight stacks for proper alignment 

and operation.

Correct all improper alignment and operation 

issues immediately.

Inspect guide rods for lubrication.

Wipe Weight Stack Guide Rods clean over entire 

length. Lubricate with a light coat of medium 

weight automotive engine oil.

Yearly Procedures

Replace all cables and belts annually

Summary of Contents for Bravo Lift































Reviews: