background image

CyberResearch

® 

Serial Communications 

 

ETS 2604 

CyberResearch, Inc

.  

iii

 

25 Business Park Drive 

 

P: (203) 483-8815; F: (203) 483-9024 

Branford, CT USA 

 

www.cyberresearch.com 

 

©Copyright 2008 

All Rights Reserved. 

 

February 

6

th

 2008 

 
 
 
The information in this document is subject to change without prior notice 
in order to improve reliability, design, and function and does not represent 
a commitment on the part of CyberResearch, Inc. 
 
In no event will CyberResearch, Inc. be liable for direct, indirect, special, 
incidental, or consequential damages arising out of the use of or inability 
to use the product or documentation, even if advised of the possibility of 
such damages. 
 
This document contains proprietary information protected by copyright.  
All rights are reserved. No part of this manual may be reproduced by any 
mechanical, electronic, or other means in any form without prior written 
permission of CyberResearch, Inc. 
 

Trademarks 

 
“CyberResearch,” and “ETS 2604,” are trademarks of CyberResearch, Inc. 
Other product names mentioned herein are used for identification 
purposes only and may be trademarks and/or registered trademarks of 
their respective companies.  
 

• NOTICE • 

 
CyberResearch, Inc. does not authorize any CyberResearch product for 
use in life support systems, medical equipment, and/or medical devices 
without the written approval of the President of CyberResearch, Inc. Life 
support devices and  systems are devices or systems which are intended 
for surgical implantation into the body, or to support or sustain life and 
whose failure to perform can be  reasonably expected to result in injury. 
Other medical equipment includes devices used for monitoring, data 
acquisition, modification, or notification purposes in relation to life 
support, life sustaining, or vital statistic recording. CyberResearch 
products are not designed with the components required, are not subject 
to  the testing required, and are not submitted to the certification required 
to ensure a level of reliability appropriate for the treatment and diagnosis of 
humans. 

Summary of Contents for ETS 2404





























Reviews: