OM750ATLCD/OM900ATLCD/OM1500ATLCD
User’s Manual
K01-C000102-02
IMPORTANT SAFETY INSTRUCTIONS
(SAVE THESE INSTRUCTIONS)
This manual contains important safety instructions. Please read and follow all instructions carefully
during installation and operation of the unit. Read this manual thoroughly before attempting to unpack,
install, or operate your UPS.
CAUTION!
To prevent the risk of fire or electric shock, install in a temperature and humidity controlled
indoor area free of conductive contaminants. (See the specifications for the acceptable temperature and
humidity range.)
CAUTION!
To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid
exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space
heaters or furnaces.
CAUTION!
Do not attach non-computer-related items, such as medical equipment, life-support
equipment, microwave ovens, or vacuum cleaners to UPS.
CAUTION!
Do not plug the UPS input into its own output.
CAUTION!
Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any
other liquid-containing vessels on or near the unit.
CAUTION!
In the event of an emergency, press the OFF button and disconnect the power cord from the
AC power supply to properly disable the UPS.
CAUTION!
Do not attach a power strip or surge suppressor to the UPS.
CAUTION!
Internal battery voltage is 12Vdc. Sealed, lead-acid, 6-cell battery.
CAUTION!
Servicing of batteries should be performed or supervised by personnel knowledgeable of
batteries and the required precautions. Keep unauthorized personnel away from batteries.
CAUTION!
When replacing the batteries, use the same number and type of batteries.
CAUTION!
Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the
battery or batteries. Released electrolyte is harmful to the skin and eyes.
CAUTION!
Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION!
A battery can present a risk of electric shock and high short circuit current. The following
precaution should be observed before replacing batteries: (1) Remove watches, rings, or other metal
objects.(2) Use tools with insulated handles.(3) Wear rubber gloves and boots.(4) Do not lay tools or
metal parts on top of batteries. (5) Disconnect charging source prior to connecting or disconnecting
batteries terminal.
INSTALLING YOUR UPS SYSTEM
UNPACKING
Inspect the UPS upon receipt. The box should contain the following:
(a)UPS (b) User Manual(c) USB Cable
*PowerPanel® Personal Edition software is available on our website. Please visit
www.cyberpower.com and go to the Software Section for free download.
OVERVIEW
TheOM750ATLCD/OM900ATLCD/OM1500ATLCD provides automatic voltage regulation for inconsistent
utility power, and battery backup during power outages. The OM750ATLCD/OM900ATLCD/
OM1500ATLCD ensures consistent power to your computer system and its included software will
automatically save your open files and shutdown your computer system during a utility power loss.
HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT
1.
Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS
unit’s rated capacity. If rated unit capacities are exceeded, an overload condition may occur and
cause the UPS unit to shut down or the circuit breaker to trip.
2.
There are many factors that can affect the amount of power that your computer system will require.
For optimal system performance keep the attached load below 80% of the UPS’s rated capacity.
HARDWARE INSTALLATION GUIDE
1.
Your new UPS may be used immediately upon receipt. However, recharging the battery for at least
8 hours is recommended to ensure that the battery's maximum charge capacity is achieved. Charge
loss may occur during shipping and storage. To recharge the battery, plug the UPS into an AC
outlet. The unit will charge in both the on and off position.
2.
With the UPS turned off and unplugged, connect the computer, monitor, and any equipment into the
battery power supplied outlets.
DO NOT plug a laser printer, copier, space heater, vacuum,
paper shredder or other large electrical device into the battery power supplied outlets. The
power demands of these devices will overload and possibly damage the unit.
3.
Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch
outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical
demands (e.g. air conditioner, refrigerator, copier, etc.) Avoid using extension cords.
4.
Depress the power switch to turn the UPS on. The power on indicator light will illuminate and the
UPS will "beep".
5.
If an overload is detected, an audible alarm will sound and the UPS will emit one long beep. To
correct this, turn the UPS off and unplug at least one piece of equipment from the battery power
supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and then turn the
UPS on.
6.
To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
7.
To store your UPS for an extended period, cover it and store with the battery fully charged.
Recharge the battery every three months to ensure battery life.
BASIC OPERATION
FRONT PANEL DESCRIPTION
1. LCD
Display
The LCD will display the UPS status including input voltage, output voltage, runtime, percentage of
load and battery etc.
2.
Power On/Off Switch
Press the power switch to turn the UPS ON or OFF.
3.
LCD Function Button
This button is used to select the LCD display contents Including input/output voltage and estimated
run time, etc. Press this button simultaneously for 3 seconds to disable or enable the alarm system
while in battery mode.
REAR PANEL DESCRIPTION
1. USB
Port
This port allows connection and communication from the USB port on the computer to the UPS.
The UPS communicates its status to the
PowerPanel
®
Personal Edition
software.
2.
Communication Protection Ports
Communication protection ports will protect any standard modem, fax, telephone line, or network
cable.
3.
TV Coaxial Terminal
Protects devices such as cable modems, DSS, and cable TV modules.
4.
Input Circuit Breaker
The circuit breaker provides overload protection.
5.
Input power cord
Connect to utility power.
6.
Surge Protected Outlets
Provides surge protection for devices that don’t require battery backup.
7.
Battery Backup & Surge Protected Outlets
Provides battery backup and surge protection. They ensure power is provided to connected
equipment over a period of time during a power failure.
