CyberPower OLS1000E User Manual Download Page 2

 

Copyright ©  2012 CyberPower Systems, Inc.

 

IMPORTANT SAFETY INSTRUCTIONS

 

 

 

This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the 
unit. Read this manual thoroughly before attempting to unpack, install, or operate the UPS. 

 

CAUTION!   

The  UPS  must  be  connected  to  a  grounded  AC 

power  outlet  with  fuse  or  circuit  breaker  protection.  DO  NOT 
plug the UPS into an outlet that is not grounded. If you need to 
power-drain this equipment, turn off and unplug the unit.

 

CAUTION!   

The  battery  can  power  hazardous  components 

inside the unit, even when the AC input power is disconnected.

 

CAUTION!   

The  UPS  should  be  placed  near  the  connected 

equipment and easily accessible. 

CAUTION!   

To prevent the risk of fire or electric shock, install 

in  a  temperature  and  humidity  controlled  indoor  area,  free  of 
conductive  contaminants.  (Please  see  specifications  for 
acceptable temperature and humidity range).

 

CAUTION!    (No  User  Serviceable  Parts):

  Risk  of  electric 

shock, do not remove cover. No user serviceable parts inside. 
Refer servicing to qualified service personnel.

 

CAUTION!    (Non-Isolated  Battery  Supply): 

Risk  of  electric 

shock,  battery  circuit  is  not  isolated  from  AC  power  source; 
hazardous  voltage  may  exist  between  battery  terminals  and 
ground. Test before touching.

 

CAUTION!   

To  reduce  the  risk  of  fire,  connect  the  UPS  to  a 

branch  circuit  with  10  amperes  (OLS1000  /  OLS1500)  /  16 
amperes 

(OLS2000/ 

OLS3000) 

maximum 

over-current 

protection in accordance to CE requirement.

 

CAUTION!   

The AC outlet where the UPS is connected should 

be close to the unit and easily accessible. 

CAUTION!   

Please  use  only  VDE-tested,  CE-marked  mains 

cable, (e.g. the mains cable of your equipment), to connect the 
UPS to the AC outlet.

 

CAUTION!   

Please  use  only  VDE-tested,  CE-marked  power 

cables to connect any equipment to the UPS. 

CAUTION!   

When  installing  the  equipment,  ensure  that  the 

sum  of  the  leakage  current  of  the  UPS  and  the  connected 
equipment does not exceed 3.5mA.

 

CAUTION! 

The OLS1000 / OLS1500 / OLS2000 / OLS3000 / 

Battery  module  models  are  only  qualified  maintenance 
personnel may carry out installations.

 

CAUTION!   

Do  not  unplug  the  unit  from  AC  Power  during 

operation,  as  this  will  invalidate  the  protective  ground 
insulation. 

CAUTION!   

To  avoid  electric  shock,  turn  off  and  unplug  the 

unit before installing the input/output power cord with a ground 
wire.  Connect  the  ground  wire  prior  to  connecting  the  line 
wires! 

CAUTION!   

Do not use an improper size power cord as it may 

cause damage to your equipment and cause fire hazards. 

CAUTION!   

Wiring must be done by qualified personnel.

 

CAUTION!    DO  NOT  USE  FOR  MEDICAL  OR  LIFE 
SUPPORT  EQUIPMENT!

    Under  no  circumstances  this  unit 

should  be  used  for  medical  applications  involving  life  support 
equipment and/or patient care.

 

CAUTION!    DO  NOT  USE  WITH  OR  NEAR  AQUARIUMS!

   

To  reduce  the  risk  of  fire,  do  not  use  with  or  near  aquariums.   
Condensation  from  the  aquarium  can  come  in  contact  with 
metal electrical contacts and cause the machine to short out. 

CAUTION!   

Do  not  dispose  of  batteries  in  fire  as  the  battery 

may explode. 

CAUTION!   

Do  not  open  or  mutilate  the  battery,  released 

electrolyte is harmful to the skin and eyes. 

CAUTION!   

A battery can present a risk of electric shock and 

high  short  circuit  current.  The  following  precaution  should  be 
observed when working on batteries 

1.  Remove watches, rings or other metal objects. 

2.  Use tools with insulated handles. 

CAUTION!   

The  unit  has  a  dangerous  amount  of  voltage. 

When  the  UPS  indicators  is  on,  the  units  may  continue  to 
supply  power  thus  the  unit’s  outlets  may  have  a  dangerous 
amount  of  voltage  even  when  it’s  not  plugged  in  to  the  wall 
outlet. 

CAUTION!   

Make  sure  everything  is  turned  off  and 

disconnected  completely  before  conducting  any  maintenance, 
repairs or shipment. 

CAUTION!   

Connect  the  Protection  Earth  (PE)  safety 

conductor before any other cables are connected. 

WARNING!    (Fuses): 

To  reduce  the  risk  of  fire,  replace  only 

with the same type and rating of fuse. 

DO  NOT  INSTALL  THE  UPS  WHERE  IT  WOULD  BE 
EXPOSED  TO  DIRECT  SUNLIGHT  OR  NEAR  A  STRONG 
HEAT SOURCE! 

DO  NOT  BLOCK  OFF  VENTILATION  OPENINGS  AROUND 
THE HOUSING! 

DO  NOT  CONNECT  DOMESTIC  APPLIANCES  SUCH  AS 
HAIR DRYERS TO UPS OUTPUT SOCKETS! 

SERVICING OF BATTERIES SHOULD BE PERFORMED OR 
SUPERVISED 

BY 

PERSONNEL 

KNOWLEDGE 

OF 

BATTERIES  AND  THE  REQUIRED  PRECAUTIONS.  KEEP 
UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES!

 

Summary of Contents for OLS1000E

















Reviews: