manualshive.com logo in svg

Custom Audio Electronics MODUS3, User Manual

Share
Download
Custom Audio Electronics MODUS3 User Manual Download Page 35

5.4  Communication parameters

This device allows the coniguration of the parameters listed in the following table. 

The parameters marked with the symbol 

D

 are the default values.

Settings remain active even after the device has been turned off

RS232 BAUD RATE

Communication speed of the serial interface:

1200 19200
2400 38400
4800 57600
9600 115200 

D

This parameter is valid only with serial interface.

RS232 DATA LENGTH

Number of bit used for characters encoding:

7 bits/char
8 bits/char 

D

This parameter is valid only with serial interface.

RS232 PARITY

Bit for the parity control of the serial interface:

None 

D

 =  parity bit omitted

Even = 

even value for parity bit

Odd = 

odd value for parity bit

This parameter is valid only with serial interface.

RS232 HANDSHAKING

Handshaking:

XON/XOFF =  software handshaking
Hardware 

D

 =  hardware handshaking (CTS/RTS)

This parameter is valid only with serial interface. When the receive buffer is full, if 
handshaking is set to XON/XOFF, the device sends the XOFF (0x13) on the serial port. 
When the receive buffer has cleared once again, if handshaking is set to XON/XOFF, 
the device sends the XON (0x11) on the serial port.

BUSY CONDITION

Activation mode for Busy signal:

OffLine/ RXFull =  busy signal is activated when the device is both in OffLine status 

and the buffer is full

RXFull 

D

 = 

busy signal is activated when the buffer is full

This parameter is valid only with serial interface.

35

Summary of Contents for MODUS3













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands