4
Program Menus GEMTS/SS Brewer
P-Maintenance
Brew By Time
Brew By Volume
Displ. Brew Time
Pre-infusion
Pulse Brew
By-Pass
Model Select
P-Maintenance
(Factory set to OFF)
Press
to Select, Set gallons brewed to indicate P-Maintenance. Press < or > to adjust from Off to 9500 gallons. This
feature advances in 100 gallon increments. Press
to exit.
Beeper On/Off
(Factory set to ON)
Press
to display ON or OFF. Pressing either < or > toggles between on and off.
to set. When ON, this feature allows
you to hear a short beep each time a button is pressed.
Drip-out Mode
(Factory set to 2 minutes)
Press
to Select. Press < or > to move to desired time. Settings are OFF, 1, 2, 3, 4 and 5 minutes. Press
to Select
time.
Warmers Default
(Factory setting - MED)
Press
to Select. Press < or > to adjust from OFF, HIGH, MED or LOW. Power setting for HIGH is 100W watts MED is
82 watts. LOW is 66 watts.
Displ. Brew Time
(Factory set to ON)
Press
to display ON or OFF. Pressing either < or > toggles between on and off. After Display Brew Time an EXIT screen
will return you to Non-Brew Prog.
Drip-out Mode
Beeper On/Off
Warmers Default
BREW BUTTON PROGRAMMING
Brew by Volume
(Factory settings: LARGE 200oz ±8oz. MEDIUM 132oz±4oz. SMALL 64oz±4oz.)
Press
to Select. Display will ask you to select a brew button, Large, Medium or Small. Press the desired brew button to
begin... when desired volume is reached press the same brew button to stop the flow. Now the volume has been set.
Brew by Time
(Factory settings: LARGE 5min-25sec. MEDIUM 3min-32sec. SMALL 1min-52sec.)
Next item in the sequence is Brew by Time. Press
to Select to change the brew time. Display will now show the current
time. By pressing < or > you can toggle back and forth from minutes to seconds to exit (ex). Change the time or set and exit
by pressing the
button.
Pre-Infusion
(Factory Disabled)
Press
to Select. Current setting in seconds is displayed < to decrease or select > to increase (range from OFF to 10
through 60 seconds),
to set.
If Pre-infusion is selected (ON), Cold Brew Lock is set within 5ºF of set point and Cold Brew Lock disappears from the list of
program selections. When Pre-infusion is ON, Pulse Brew disappears from the list of program selections.
Pulse Brew
(Factory setting C)
Press
to select, < or > to select OFF or one of five pulse patterns (A to E) . The five Pulse Brew options help “tune” or
change the coffee flavor.
Guidelines for Pulse Brew:
Filter Pack type coffees typically extract better with the
A
and
B
pulse setting.
Decaf coffees typically extract better with the
B
pulse setting.
High-Yield coffees typically extract better with the
C
pulse setting. Of course, any of the
A, B
or
C
settings may be used to
suit your taste profile.
Settings
D
and
E
are manual pulse counts.
To exit from the Pulse Brew mode, select
0
for the time.
If Pulse Brew is on, Cold Brew Lock is set within 5ºF of set point and Cold Brew Lock disappears from the list of program
selections. When Pulse Brew is on, Pre-infusion disappears from the list of program selections.
By-Pass
(Factory settings: LARGE 35%. MEDIUM 10%. SMALL Off.)
The By-Pass option helps with controlling extraction with larger brews. Contact time that is too long will extract undesirable
bitter, harsh flavor compounds. By-passing some of the brew water around the coffee bed will balance the extraction.
Press
to display current setting. Press < or > to change settings; OFF, 5% to 50%, in 5% increments. Press
to set.
Model Select
(Factory set to Gemini-Twin IF)
Press
to select, < or > to select model. The selections are: ThermoPro-Twin, ThermoPro-Single, Gemini-Twin, Gemini-
Single, Milano-Twin, Milano-Single, Gemini-Twin IF, and Gemini-Single IF. Press
to set. When the Model Select feature is
changed, all settings are reset to the defaults of the newly selected model.
