background image

8

Safety instructions

The company cannot be held liable for any print or transcription 

errors, reserving the right to make changes where deemed 

suitable without prior notice. 

Partial reproduction without the Manufacturer’s consent is 

prohibited. Measurements are purely indicative and not binding. 

The original language used to prepare this manual is English: the 

Manufacturer is not responsible for any translation/interpretation 

or print errors.

• The serial plate provides important

technical information. This is vital in

case of a request for maintenance or

repair of the equipment: please do not

remove, damage or modify it.

• WARNING - To reduce the fire hazard,

the appliance must be installed only in

rooms without combustible materials

within about 46 cm (18 inches) from

the sides, front or rear of the appli-

ance or within about 102 cm (40 inch-

es) above the appliance. The appliance

must be placed on non-combustible

surfaces and without combustible

materials in contact with the lower

side. The support surface must in any

case extend no less than about 31 cm

(12 inches) beyond the appliance on all

sides.

• Make sure that the base on which the

oven rests is fireproof, flat, stable and

able to support the weight of the ap-

pliance.

• Check that the oven rests firmly and

completely on the underlying base

with both supports, front and rear.

• (Appliances without either power cable or plug) 

The

electrical connection must be carried

out exclusively by qualified personnel

after reading the safety warnings at

the beginning of the manual.

• (Appliances without either power cable or plug) 

The

cable must be only of the type stated

and the plug fitted to it must be suita-

ble for the consumption and connec-

tion of the oven to the electrical mains.

• If required, the cable can be replaced

by the Dealer or its technical service or

by a person with similar qualifications

to prevent any risk.

Summary of Contents for MANTEGNA MN40/1DG-A5-CP


















Reviews: