background image

 

Copyright Reserved HyVISION System Inc.   

This document is Quick Start Guide (151001,En). To improve quality of product, this could be revised without 

prior notification or consent.     

HyVISION System is not liable for any losses resulted from the use of the document or any errors or offering

.

 

10 

Mounting of Filament Spool

 

  Prepare the filament spool to be used. 

Cut off the filament fixing tape and remove the 
bending filament. 

 

  Insert the spool holder into the hole at the rear of 

printer. 
Please be careful not to be fallen out of the spool 
holder. 

  Mount the filament spool into the spool holder and 

feed the filament into the insertion hole. 

Be careful of the spool rotation/insertion direction

 

  Open the top door and push the filament all the way 

into the printer body so that the filament is out of the 
Teflon tube. 

Be careful not to bend, cut or twist the filament tube. 

This may prevent the filament from being supplied 
properly.

 

 

* Filament spool sholud be mounted in the correct direction. 

Please mount the spool with the company logo and sticker faced outward. 

It is designed in a way that filament spool should be fed rotating in counter clockwise. 
It may cause the feeding problem if the spool is mounted in the wrong direction. 
Please make sure that spool is mounted correctly before printing. 

* When mounting the filament spool, any jamming object between filament spool holder and 

spool can cause malfunction. 

Remove any jamming object for smooth supply of spool when mounting the spool into the 
holder. 

* Teflon tube is the path from filament spool to extruder. The length of teflon tube is optimized 

according to the printer,    excessive force to pull the tube may cause deformation of the 
tube causing failure in feeding filament. 
Do not bend, cut or pull out the mounted teflon tube. 

 

* Pay attention filament being unwound from the filament spool left when removing the 

filament spool from the spool holder. Tie up the filament left into the filament spool while 
storing the filament. When you take out the leftover filament from filament holder, make 
sure not filament not get loose and also wind filament tightly to the spool, otherwise 
feeding will not be smooth. 

* keep the leftover filament tightly wound up to prevent any dusts and moisture. Once 

filament is open for use, please try to consume it quickly. Long exposure to the outside 
environment can cause bad print quality or miscontact to the bed, in severe cases, clogging 
from nozzle, due to the moistures. 

Spool Rotation 

Unpacking and Installation (3/4) 

 

Summary of Contents for Style 3DP-210F















Reviews: