S
ection
5— o
peration
20
Operating The PTO
Operate the PTO clutch as follows:
1.
Move the throttle control lever to approximately the mid
throttle position.
2.
Pull the PTO switch upward to the “ENGAGED” position.
3.
Advance the throttle lever to the operating speed (full
engine speed).
4.
The operator must remain in the tractor seat at all times. If
the operator should leave the seat without turning off the
power take-off switch, the tractor’s engine will shut off.
5.
The PTO clutch cannot be operated when the tractor is
driving in the reverse direction. The PTO will disengage
when both drive control levers are moved to the reverse
position, and will re-engage when one (or both) control
lever(s) is moved to the neutral or forward position.
Using the Mower Deck
WARNING!
Make certain the area to be mowed is
free of debris, sticks, stones, wire or other objects
that can be thrown by the rotating blades.
NOTE:
Do not engage the mower deck when lowered in grass.
Premature wear and possible failure of the ‘V” belt and PTO
clutch will result. Fully raise the deck or move to a non grassy
area before engaging the mower deck.
1.
Mow across slopes, not up and down. If mowing a slope, start
at bottom and work upward to ensure turns are made uphill.
2.
On the first pass pick a point on the opposite side of the
area to be mowed.
3.
Engage the PTO clutch using the PTO switch and move the
throttle control or throttle/choke control to the fast
position.
4.
Lower the mower deck to the desired height setting using
the lift handle.
5.
Slowly and evenly push the RH and LH drive control levers
forward to move the tractor forward, and keep the tractor
headed directly toward the alignment point.
NOTE:
The speed of the tractor will affect the quality of the
mower cut. Mowing at full speed will adversely affect the cut
quality. Control the ground speed with the control levers.
6.
When approaching the other end of the strip, slow down
or stop before turning. A U-turn is recommended unless a
pivot or zero turn is required.
7.
Align the mower with an edge of the mowed strip and
overlap approximately 3”.
8.
Direct the tractor on each subsequent strip to align with a
previously cut strip.
9.
To prevent rutting or grooving of the turf, if possible, change
the direction that the strips are mowed by approximately 45°
for the next and each subsequent mowing.
WARNING!
Be careful when crossing gravel paths
or driveways. Disengage the PTO and raise the deck
to the highest position before crossing..
NOTE:
When stopping the tractor for any reason while on a grass
surface, always:
•
Place the shift lever in neutral,
•
Engage the parking brake,
•
Shut engine off and remove the key.
•
Doing so will minimize the possibility of having your lawn
‘‘browned’’ by hot exhaust from your tractor’s running engine.
Checking the Safety Interlock Circuits
Periodically check the safety interlock circuits to ensure they are
working properly. If a safety circuit is not working as designed,
contact you Cub Cadet dealer to have the tractor inspected. DO
NOT operate the tractor if any safety circuit is not functioning
properly. To check the safety circuits, proceed as follows:
1.
Sitting in the tractor seat with both drive control levers
opened fully outward, disengage the parking brake and
momentarily turn the ignition switch to the start position.
The engine should not crank.
2.
Engage the parking brake and pull the PTO switch upward
to the engaged position. Momentarily turn the ignition
switch to the start position; the engine should not crank.
3.
Push the PTO switch downward to the disengaged position
and engage the parking brake. Start the engine and move
one of the drive control levers from the fully outward
neutral position. The engine should stop running. Repeat
the procedure with the opposite control lever.
4.
Move both control levers fully outward in the neutral
position and disengage the parking brake; then lift upward
from the operator’s seat. The engine should stop.
5.
With both control levers fully outward in the neutral
position and the parking brake engaged, engage the PTO.
Lift upward from the operator’s seat; the engine should
stop.
6.
Start the tractor, disengage the parking brake, and move
the control levers inward to the neutral operating position.
Engage the PTO and move both control lever slowly into
the slow reverse position; the PTO should disengage
and the mower deck should stop until one or both of the
control levers is moved to the neutral or forward position.
