background image

 2 

頁,共

 12 

 SWH-2109F 

V1.1 

 
 

Trademarks

 

CTS is a registered trademark of Connection Technology Systems Inc.   

Contents subject to revise without prior notice. 

All other trademarks remain the property of their owners. 

 

Copyright Statement 

Copyright 

©

 Connection Technology Systems Inc.

 

This publication may not be reproduced as a whole or in part, in any way whatsoever 

unless prior consent has been obtained from Connection Technology Systems Inc. 

 

FCC Warning 

 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates uses and can radiate radio frequency energy and, if no installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures: 
 

„

 

Reorient or relocate the receiving antenna. 

       

„

 

Increase the separation between the equipment and receiver. 

       

„

 

Connect the equipment into a different outlet from that the receiver is connected. 

       

„

 

Consult your local distributors or an experienced radio/TV technician for help. 

       

„

 

Shielded interface cables must be used in order to comply with emission limits. 

 
Changes or modifications to the equipment, which are not approved by the party 
responsible for compliance, could affect the user’s authority to operate the equipment. 
 
Copyright © 1999 All Rights Reserved.   
 
Company has an on-going policy of upgrading its products and it may be possible that 
information in this document is not up-to-date. Please check with your local distributors 
for the latest information. No part of this document can be copied or reproduced in any 
form without written consent from the company. 
 
Trademarks: 
All trade names and trademarks are the properties of their respective companies

   

Summary of Contents for SWH-2109FX













Reviews: