CTI GG-2 Installation And Operation Manual Download Page 12

12

GG-2

Maintenance

Specifications

All gas detection systems should be calibrated with certified calibration 

gas once every six months. At this interval, all alarm functions and outputs 

should be tested, verified and documented.

If sensor span or zero cannot be adjusted, the sensor may be approaching 

its end of life and must be replaced. Keep an operation log of all 

maintenance, calibrations and alarm events.

To clean the controller, use a mild cleaning solution and soft cloth.

In the unlikely event that the fuse needs to be replaced use a 3A, 250V, 

5x20mm, slow-blow type fuse.

The operator interface has a backup lithium coin battery to run the real-time 

clock and retain configuration memory while the system is powered down. A 

low battery is indicated by a battery symbol on the display. If a low battery is 

indicated, replace old battery with a Type CR2450 Li Coin Cell.

Input Power Requirements:

100-240 VAC, 1.3 A 50/60 Hz.

Output 24 VDC power available for sensors and audio/visual devices:

1.2A @ 40°C (104°F).

0.8A @ 50°C (122°F).

Dimensions: 

11.3” high x 9.3” wide x 7” deep.

Weight: 

6 lbs

Enclosure: 

Fiberglass Reinforced Polyester NEMA 4X, IP 66, with 

polyurethane gasket. Continuous stainless steel hinge. Captive screws in lid. 

For non-classified areas.

Temperature Range: 

0°F to +122°F

Humidity Range: 

0-95% RH condensing (100% intermittent), with proper 

conduit seals.

Sensor Inputs: 

(2) 4/20 mA, 350 Ohm input impedance.

Analog Outputs:

(2) Linear 4/20 mA (max input impedance: 700 Ohms).

Relay Outputs:

(6) SPDT, Form C dry contacts.

8 A @ 24 VDC or 10 A @ 240 VAC.

Terminal Block Plugs (Field Wiring):

26-12 AWG, torque 4 lbs-in.

User Interface: 

LCD illuminated screen. Graphic display screen: 128 x 64 

pixels. 8 lines x 22 characters. 16 sealed membrane switches.

Certification:

SGS Listed: Conforms to UL 61010-1

Certified to CSA C22.2 No. 61010-1

Summary of Contents for GG-2

















Reviews: