CTI GG-2 Installation And Operation Manual Download Page 11

11

GG-2

Contrast

Adjust contrast to allow for best 

viewing of LCD.

Relay Test

The relay test menu allows the relay 

outputs to be tested individually 

for correct output functions. Select 

the relay to be tested with the 

alphanumeric keys.

Press YES to Set relay. NO to exit.

Relay has been set. Press NO to clear 

the relay and exit once the relay 

output function has been verified.

ESC back to Config main menu. Press 

YES to save changes. Press ESC again 

to exit without saving changes.

Latch for Warn Relay: Allows warning 

relay of channel being programmed to 

latch. A latched relay must be cleared 

by pressing the RESET button, once 

the gas has cleared.
Horn: Allows horn relay and buzzer to 

activate during a Warn condition.

Alarm Setpoint: Use this field to 

change the default alarm setpoint.

Direction: Use this field to change the 

default direction setting. For example, 

oxygen level monitoring may require 

downscale alarming.
Latch for Alarm Relay: Allows alarm 

relay of channel being programmed 

to latch once activated. A latched 

relay must be cleared by pressing 

the RESET button, once the gas has 

cleared.

Location Name: Use this field to 

name the location of the sensor being 

programmed. To delete the existing 

label, ENTER and then PREV to delete 

characters.

ESC to return to Config menu.

Clock

Set current time and date.

Summary of Contents for GG-2

















Reviews: