CTI Products RadioPro Installation Manual Download Page 30 | Manualshive

Page: 30 / 46

CTI Products RadioPro Installation Manual Download Page 30

RadioPro IP Gateway

Installation and Configuration Guide NEXEDGE NX-57xx/58xx

30

f.

Network tab

Do

NOT

use leading zeros for any

of the address fields.

DHCP

should

NOT

be selected unless an

engineer at CTI Products is
consulted.

The default

TCP Port

# is 48222.

This can normally be left at its
default value.

An entry for default

Gateway

is

needed only if RadioPro clients
(Dispatch, Solo, Talk, Talk for
Mobile) will be accessing this IP
Gateway from another network, or
the Internet.

An entry for

DNS Server

is needed only if an NTP server host name was specified in the General

tab (instead of an IP Address). If an NTP server host name is not specified, then

DNS Server

should be blank or

0.0.0.0

.

g.

Radio Aliases tab

This tab is used to create Alias
Names for radio IDs. The Alias
Names listed on this tab will be
displayed in the contact list for
RadioPro Solo, Talk, and Talk for
Mobile clients.

«
...
28
29
30
31
32
...
»

Summary of Contents for RadioPro















































Reviews:

No comments