manualshive.com logo in svg

CTC Union STE-10, Operation Manual

Share
Download
CTC Union STE-10 Operation Manual Download Page 30

Chapter 2: Application Examples

26

2.3  Auto Telnet Mode Application

The application provides a very transparent connection for RS-

232 over Ethernet using the TCPIP protocol stack. In our example, we

are again connecting to an ETU01-A control port for management. The

ETU01-A side will have one 

STE-10

 configured in Raw Mode and

connected to Ethernet. The remote terminal side will have another

STE-10

 connected to Ethernet and configured to "auto" telnet to the

ETU01-A side's 

STE-10

. The next figure is a simple example of this

application.

Auto Telnet and Raw Mode Access provides transparent connection.

The right side 

STE-10

 unit is configured in Raw Mode, set an IP

address and port number, with serial port configured for the ETU01-A

(9600,8,N,1 no handshaking). The left side 

STE-10

 Terminal Server is

configured in auto Telnet mode, pointing to the right side's IP address

and port number. Its serial port is configured for the serial terminal

(9600,8,N,1 no handshaking).

Summary of Contents for STE-10





































Reviews:

No comments

Brands by name

Popular brands

Load more brands